1. Safety & environmental Information
The T RA INED PRO JEC TIONIST S ma y only perform the maintenance task described in the User & Installation manual. All other
maintenance t asks and service tasks must be performed by qualified SERVICE PERS ON NEL.
The DLP Cinem a Systems are intended "FOR PROFE SSIONA L USE O NLY" by AUTH OR IZED PERSONNE L familiar w ith potential
hazards associated with high voltage, high intensity light beams generated b y lasers. Only qualified SERVICE P ERS ONNE L and
TRAINED P ROJE CTIONIST S, kn owledgeable of such risks, are allowed to perform service functions inside the product enclosure.
Restricted access location
To protect untrained persons and children, the projector must be installed in a restricted access loc ation. The definition of a
restricted access location is a loc ation for equipm ent where both of the following paragraphs apply:
• Access can only be gained by skilled persons (installer or service personnel) or by operators who have been ins tructed and
trained by a skilled person. The persons must have been instructed about the re asons for the restriction applied to the location
and about the precautions that shall be taken.
• Access is only possible through the use of the tool or lock and key, or other m eans of s ecurity, and is controlled by the authority
responsible for the location.
Why a r estricted access loc ation: This product us es an extremely high brightness lamp. No person is allowed to look directly into
the lens or lamp. N o person is also allowed to touch the exhaust system, due to hot exhaust air.
This shall be phy sically imposs ible b y creating s ufficient separation height or by placing optional barriers. W ithin the restricted area
operator training is cons idered sufficient.
Owner ’s record
The part n umber and serial number are printed on a label which is stuck on the respective part. Record these num bers in the spaces
provided below. R efer to them wh enever you call upon your Barco dealer regarding this product.
Product article number
Product serial number
Dealer
1.2 Important safety instructions
To prevent the risk of electrical shock
• This projector should be operated from an A C power source. Ensure that the mains voltage and capacity matches the projector
electrical ratings. If you are una ble to install the AC requirements, contact your electrician. Do not defeat the purp ose of the
grounding.
• Installation according to the loc al electrical code and regulations by qualified technical personnel o nly.
• This product is equipped with a three-terminal barrier strip for the connec tion of a m ono p hase line with a s eparate earth ground
PE. If you are unable to install the A C Requirements, contact y our electrician. Do not defeat the purpose of the grounding.
• The cross-sectional area of the conductors in the power supply cord shall be not less than 4 mm
2
or AWG 10.
• The electronics o f the projector must be powered either from a suitable UPS unit or from the power outlet socket (UPS OU TLET )
provided on the projector. For that reason an adapted short power cord (2-pole 3-wire grounding) is added to the p rojector
accessories to loop through the power.
• The provided power output socket (UPS OUTLE T) on the projector may only be used to provide power to the projector elec-
tronics. Never connect other devices to this power output s ocke t.
• The circuit breaker(s) that must be provided in the power circuit(s) of the projector is considered as general disconnect switch(es)
to s witch off the complete installation.
• Switch off the projector and unplug the power cord from the UPS INLET for removal of all pow er from the projector.
• Warning: High leakage current. Earth connection essential before connecting supply.
• Do not allow anything to rest on the power cord. Do not locate this pr ojector where persons will walk on the cord.
• Do not op erate the projector with a damaged cord or if the projector has b een dropped or damaged - until it has been examined
and approved for operation by a qualified service technician.
• Position the cord so that it will not be tri
pped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a cur rent rating at least equal to that of the projec tor should be used . A cord rated
for less amperage than the projector may overh eat.
• Never pus h objects of any kind into this projector t hrough cabinet s lots as they may touch da ngerous voltage po ints or short
circuit parts that could result in a risk of fire or electrical shoc k.
• Do n ot expose this projector to rain or mois ture.
• Do not immerse or expose this projector in w
ater or other liquids.
2
R59770352 DP2K-C SERIES 22/03/2017
To Next Page
Loading...
Need help?
General
