Bogen Classic Series User Manual

TECHNICAL SPECIFICATIONS
Power Output:
Ouq)ut Connections: Screw-type te rminals;
C55—35WRMS
TAPE/BOOSTER jack; provisions for WMT-IA
C60—60WRMS
Controls: MIC 1, MIC 2/AUX 1 {selector-switch), AUX
croo—100WRMS
2, BASS, TREBLE. TEL
Distortion: Less than ^%, 70H2 to I6KH2 @ -2dB.
Tone Control Action:
4-Ohm Direct Ouput— 0.5%, 2OI2 to 2CMCH2 at
7reb/e—±11dB at 10kH2
rated power
Bass—±11dB at100H2
Frequency Response:
Power Requirements: 120VAC, 6OH2
7OH2 to IOKH2, ±2dB @ -2dB
C35— 85 watts
4-011111 Direct Ouput— 2OH2 to 2OKH2 ±1dB
C60—148 watts
Hum and Noise:
C/CO—220 WQtts
MiC Input 55dB below rated output
Overload Protection: Electronic overload protection
AUX input 70dB below rated output
Thermal Protection: Thermistor attached to heat sink
TEL 70dB below rated povwr
Electrical Protection: Circuit breaker
Input Sensitivity:
Dimensions:
MiC Lo-Z Balanced— 600pV
C35— 14-1/2"W X S-SM-H x 10-5/8"D
AUX—BbmM
(37 X 9.6 X 27cm)
TEL —75mV
060, C100— 14-1/2'Wx S-SMTH x 11 "D
Outputs:
(37 X 9.6 X 28cm)
8,16 ohms, 25V, and 70V balanced;
Shipping Weight:
4 ohms unbalanced.
C35—15 lbs.
Input Connections: Tvto MIC Lo-Z te rminals, two AUX
.C60—18 lbs.
Hi-Z jades, Tel
C/00— 20 lbs.
.I";
Hie Bogen Classic Series models CSS, C60,andC100 are
the latest evolutioii of die long line of pc^ular C Series of
amplifiers.fiom Bogen Communications. Th^ surpass pre
vious models inbodi peifomm^ and flexibUi^, and include
new features and sle^ 1990*s sQ^lingi Ihe models are rated
at 35 watts, 60 watts, and 100 watts.
Each Classic Series amplifier offers a choice of inputs: 2
Lo-Z balanced microphone inputs and 1 Aux input, or 1 Lo-Z
microphone and 2 Aux inputs. A TEL input is also provided
to permit paging from a telephone. A built-in microphone
precedence circuit lets you mute the Aux 2 channel with die
use of a customer-supplied switch. This lets you mute back
ground music from a tuner, CD or cassette player when you
mate a public address aimouncement. Independent volume
controls are provided for each input. Treble and bass controls
offer tonal balance.
Output screw terminal connections are provided for 8 and
16 ohm balanced and 4-ohm unbalanced systems, and also
for 25-volt and 70-volt constant-voltage speaker systems.
Output jacks let you patch into a tape recorder or an additional
(booster) amplifier. An accessory transformer, Bogen Model
WMT-IA, can be installed to allow output-matching to a
telephone line.
The amplifiers operate fixim a 120VAC, 60Hz source and
are equipped with thermal breaker, electronic overload and
electrical circuit breaker protection.
INSTALLATION
UNPACKING
The amplifier was carefiilfy checked before leaving the
factory. Inspect the shipping container and unit carefully for
indication of improper handling. If the unit has been dam
aged, make an immediate claim to the distributor from whom
it was purchased. If the an^lifier was shaped directly to you,
notify the transportation comparq' without delay and place
your claim.
POWER AND GROUNDING
The AC line cord has a three-prong plug which must be
plugged into a three-wire grounded 120-volt, 60Hz outlet. It
is important to ground the amplifier properly.
INPUT CONNECTIONS
MICROPHONES: Two low-impedance balanced micro
phones may be connected simultaneously to the screw termi
nals on the rear panel of the amplifier.

Bogen Classic Series Specifications

General

Brand	Bogen
Model	Classic Series
Category	Amplifier
Language	English