Bogen's Power Vector modular input amplifier series consists of five models, ranging from 35 to 250 watts of
power. Each model accepts up to 8 plug-in modules with 4 levels of priority between modules. Two module bays
also accept signal-processing output modules.
Each input has its own independent volume control and a signal/clip indicator. An 11-segment LED meter indicates
output level, while a motorized master volume control allows smooth and accurate operation of the unit's master
volume control from a remote control panel (sold separately).
Five amplifier models
offer minimum power
handling capacity of 35,
60, 100, 150, and 250 watts
and each has a
substantial power reserve.
(Typical reserve power@1kHz)
FEATURES LIST:
• 5 models ranging from 35W to 250W, with
a large power reserve
• Capable of handling 70V, 25V, 8-ohm,
and 4-ohm speaker loads
• 8 module bays
• Wide selection of advanced plug-in modules
(see pages 3 & 4)
• 2 module bays capable of handling signal
processing output modules
• 4 levels of priority between modules
• 11-segment LED output level meter monitors the
output level of the power amplifier, with Peak
and Average meter switch
• Motorized master volume control that can
be remotely operated
• Two-color LED for each input channel indicates input
signal and clipping
• Master Mute function overrides all audio from the
mixer section of the amplifier
• Lockable switch permits user to select either
transformer-coupled outputs or a direct
low-impedance output
• Bass and treble controls with bypass switch
• 3 priority mute buses are available externally
for system expansion and external control
• Bridging connection available for expanding number
of Power Vectors in a system
• 125 Hz Lo-cut switch
• Signal processing insert jacks allow external
equipment to be inserted between the pre-amp
output and the power amp input
• Pre-EQ, unbalanced, buffered output signal “post”
all unit controls, but “pre” any external signal
processing equipment inserted
• Grounded convenience receptacle
• 8 Module Security Covers (PVMC) included
(not on Wall Mount units) (see below)
• Front panel security cover (PVSC) with break-away
access tabs available (see below)
• 2 rack spaces high (3-1/2")
• UL/cUL listed
Power Vector Amplifier
Product Features
Performance Specifications
Power Handling
Power Vector Amplifiers, Power Vector Amplifiers, Power Vector
Rack-Mount (V-Series) Wall-Mount (WV-Series) Mixer
MODELS:
(Model Number:
Power Output Rating**)
Frequency Response
Transformer: 45 Hz-20 kHz; 0/-2 dB 45 Hz-20 kHz; 0/-2 dB +/- 1 dB
(20 Hz to 20 kHz)
Direct: 20 Hz-20 kHz; 0/-1 dB 20 Hz-20 kHz; 0/-1 dB ----------
Distortion
Transformer: 0.5%** 0.5%** 0.01%†
Direct: 0.1%**
(.05% typical @ 1 kHz) 0.1%** -----------
Signal-to-Noise†
Fundamental: -94 dB -94 dB -99 dB
With AUX Module: -70 dB -70 dB -94 dB
With MIC Module: -60 dB -60 dB -64 dB
With TEL Module: -70 dB -70 dB -92 dB
Tone Controls
Bass Frequency: 100 Hz
(+/- 10 dB minimum) 100 Hz (+/- 10 dB minimum) 100 Hz (+/- 10 dB minimum)
Treble Frequency: 10 kHz (+/- 10 dB minimum) 10 kHz (+/- 10 dB minimum) 10 kHz (+/- 10 dB minimum)
Low Cut Frequency: 125 Hz (@ -6 dB/octave) 125 Hz (@ -6 dB/octave) 125 Hz (@ -6 dB/octave)
Sensitivity 0.4V (at module bay connector) 0.4V (at backplane connector) 0.4V (at backplane connector)
Output Regulation 2 dB or better, no load to full load 2 dB or better, no load to full load ---------
Output Impedance
Transformer-Coupled: 70V, 25V, 8 ohms (bal or unbal) 70V, 25V, 8 ohms (bal or unbal) ---------
Direct Coupled: 4 ohms 4 ohms ---------
Balanced: --------- ---------
50 ohms @ -4 dBu, 600 ohms
@ -10 dBu, 5 ohms @ -50 dBu
Unbalanced: --------- --------- 100 ohms
Output Level
Balanced: --------- ---------
Selectable +4, -10, -50 dBu
(typical when meter reads "0");
+18 dBu max.
Unbalanced: --------- --------- 0 dBu (typical when meter
reads "0"); + 20 dBu max.
Inserts
Insert "OUT" Level: 1 VRMS (@ FRP) --------- ---------
Insert "OUT" Impedance: 50 ohms maximum --------- ---------
Insert "IN" Sensitivity: 1 VRMS --------- ---------
Insert "IN" Impedance: 10k ohms minimum --------- ---------
Pre-EQ Output (on V Series);
Tape Out (on WV Series)
Output Level: 4 VRMS (@ FRP) 4 VRMS (@ FRP) ---------
Output Impedance: 50 ohms maximum 50 ohms maximum ---------
Signal/Clip Indicator
Signal Detect Threshold: 10 mV @ output of module 10 mV @ output of module 10 mV @ output of module
Signal Indicator Hold Time: 50 mS green indicator 50 mS green indicator 50 mS green indicator
Clip Detect Threshold: 6V @ output of module 6V @ output of module 6V @ output of module
Clip Detect Hold Time: 50 mS red indicator 50 mS red indicator 50 mS red indicator
AC Power Receptacle
500W max. power, unswitched
----------
500W max. power, unswitched
AC Voltage 120V AC, 60 Hz 120V AC, 60 Hz 120V AC, 60 Hz
AC Current
V250: 5.5A; V150: 3.5A; V100: 2.0A;
WV250: 5.5A; WV150: 3.5A; 0.2A
V60: 1.3A; V35: 0.6A WV100: 2.0A
Product Weight
V250: 40 lb.; V150: 35 lb.; V100: 32 lb.; WV250: 28 lb.; WV150: 29 lb.;
18 lb.
V60: 28 lb.; V35: 24 lb. WV100: 27 lb.
Dimensions 17-1/4" W x 3-7/8" H x 14-3/4" D 17-1/4" W x 3-7/8" H x 14-3/4" D
(all models)
V250: (250W / 340W*) WV250: (250W / 340W*) VMIX
V150: (150W / 200W*) WV150: (150W / 200W*)
V100: (100W / 140W*) WV100: (100W / 140W*)
V60: (60W / 85W*)
V35: (35W / 45W*)
* Typical, @ 1 kHz/0.1% THD/4 ohms ** THD+N, Maximum, full bandwidth @ FRP
† Referenced to FRP output level, 20 Hz-20 kHz bandwidth limited
WV100/150/250: 14-1/8" W x 21" H
BBF: 14-1/2" W x 24- 3/4" H x 3-7/8” D
BBS: 16-1/4" W x 26- 3/4" H x 3-7/8” D
WMAD: 16-1/4" W x 26- 3/4" H x 1” D
To Next Page
Loading...
Need help?
General
