Casio CZ-1 User Manual

KEY
SPUT
MODE
^IKEYfiSPLniSETinNGS
With the
CZ-1,
two tones can be
assigned
to the
upper
and lower ranges of the keyboard. The
split point
of
the
keyboard
and the
individual volumes
of the two
tones
can
be
freely set,
and effects
can be set to ON and OFF.
(1)
SPLIT POINT
SETTING
Press the
KEY SPLIT key
in the
Mode
Select
Section.
SPLIT
POINT
=
24
SP
24
LOUER
LEU=15
UPPER
LEU=15
n
LOWER tone
level
(1-15)
Cursor
UPPER
tone
level
(1-15)
Use
the
CURSOR keys to
move the
cursor
to
the SPLIT
POINT
value.
Use the
VALUE keys
to set
the value
within
a
range
of 1
through 60.
This
determines the
split
point.
1
10
20 30
40 50
60
iiiiiiiiiiliiiiiiiiiii iiidii
SPLIT
POINT
=
24
(2)
TONE
AND VOLUME
LEVEL
®
Use
the
B
CURSOR key
to
move
the cursor to the
LOWER
LEVEL value. Here, the
LOWER tone
and
volume
level
are
set.
•Select
one of
the internal
or
cartridge
tones using the
Programmer Section. The
tone
selected
will
be
play-
able
to
the
left
of the
split point.
•The
VALUE keys
in
the Data
Entry Section are
used
to
set the
volume level
within
a
range
of
1
through 1
5.
A setting
of
15 represents
maximum
volume.
®
Use the
S
CURSOR key to
move
the
cursor
to the
UPPER
LEVEL
value. Select the
tone
and
set
the
volume
In the
same
way
as
for the
LOWER
LEVEL.
Now the keyboard is split
for simultaneous,
separate
play
of two tones.
(3)
SUSTAIN PEDAL
ENA/DIS
The
sustain
pedal effect can
be
applied
independently
to
the UPPER
and
LOWER tones
used
in
the
KEY
SPLIT
mode.
The display
will
appear
as illustrated in Fig. 1
when the
PAGE
UP
key
is pressed
while in the
KEY
SPLIT
mode.
(Fig.
1)
SUS.PEDRL
LCH...i=EN
a
UPF-EHfl
'
—
Cursor
'
—
ENA/DIS
'
—ENA/DIS
"ENA" is the
abbreviation of
the
word
"enable"
which
indicates
that
the pedal
effect is
applied,
while ''DIS"
or
"disable" means that the
effect is not
applied.
®When
the
cursor
is located
under the
LOWER
specification
as
shown
in
Fig.
1,
the VALUE
00
keys
can be
used
to
switch
between sustain
pedal
ENA/DIS
for the
LOWER
tone.
(5)
Moving the
cursor
to the
UPPER
specification
makes
it
possible
to use
the
VALUE
SB
keys
to
switch
between
sustain
pedal
ENA/DIS
for
the
UPPER
tone.
*Note
that
UPPER
and
LOWER
cannot both be
set
to
DIS
at
the
same
time.
"Setting
LOW
=
DIS/UPPER
=
ENA
causes
the
upper
tone
to be
held
when
the
sustain
pedal
is
depressed.
-43-

Casio CZ-1 Specifications

General

Brand	Casio
Model	CZ-1
Category	Synthesizer
Language	English