7
Helpline No: UK 0151 649 1500 / IRE 189 094 6244
GB
앬 If you interrupt your work to move to a different
position it is imperative to switch off the shredder
while you are moving there.
앬 Never use the shredder in the rain or in moist or
wet conditions.
앬 Protect the shredder from the damp and rain.
앬 Always wear suitable clothing to protect your
head, hands and feet from injury. Wear a helmet,
goggles or visor, high boots or strong shoes, long
trousers made of tough material, and work gloves.
앬 Keep the shredder away from other persons,
particularly children and pets.
CAUTION! The guard is vital for your safety
and for the safety of others, and it is also
essential for the shredder to work correctly.
Failure to observe this instruction will not
only create a potential hazard, it will also
result in the loss of your rights under the
warranty.
앬 Keep the air vents clear of dirt.
앬 After use, unplug the machine and check it for
damage.
앬 When you are not using the shredder, keep it in a
dry place out of the reach of children.
앬 Check the screws regularly to see that they are
properly tightened.
앬 The mains voltage must be the same as the
voltage specified on the rating plate.
앬 Plug connectors must be equipped with earthing
contacts and the coupling must be rain-water
protected. It is recommended that an RCD
(Residual Current Device) is fitted into the mains
supply for added safety.
- Do not use 2-core extension leads with power
tools which require an earth - always use 3-core
leads with an earth supply marked for outdoor
use.
- Always unwind any extension reels fully.
- For extension reels up to 15 metres use a wire
cross section of 1.5mm
2
. For extension cords over
15 metres but less than 40 metres, use a wire
cross section of 2.5mm
2
rated at 10 amps
앬 Use only original replacement parts for repair and
maintenance purposes.
앬 Have repairs carried out only by a qualified
electrician.
앬 Examine the shredder for signs of wear or
damage each time before you use it and after any
collisions. Have essential repairs carried out
without delay.
앬 Never use replacement parts or accessories which
are not foreseen or recommended by the
manufacturer.
앬 Pull out the power plug before carrying out any
inspection, cleaning or other work on the shredder
and whenever it is not being used.
앬 Before you begin your work, examine the material
you want to shred. Remove any foreign bodies.
Continue to watch out for foreign bodies while you
are working. If you come across any foreign
bodies while shredding, shut down the machine
and remove the items in question.
앬 Keep the machine away from other persons,
particularly children and pets.
앬 Use the machine only in the way described in
these operating instructions.
앬 Only ever connect the device to a shock-proof
socket which has been installed in accordance
with regulations and which is protected by a 16A
fuse as a minimum.
앬 The efficiency of the machine will be greatly
reduced if a connecting cable with too small a
cross section is used. A conductor cross section
of at least 3x1.5 mm
2
is required for cables up to
25 m long, and one of at least 3x2.5 mm
2
for
cables longer than 25 m.
앬 If the machine has to be lifted for transporting, be
sure to switch off the motor first and wait for the
cutter to come to a standstill. Each time before
you leave the machine, switch off the motor and
pull out the power plug. Before you connect the
machine to the power supply, make sure that the
loading funnel is properly connected to the motor
housing and the release screw tightened.
앬 If the garden refuse shredder vibrates excessively,
turn off the motor, pull out the power plug, and find
out immediately what is causing the vibrations.
Intensive vibration is usually a sign that something
is wrong.
앬 Do not wear loose clothing or clothing with
hanging belts or cords.
앬 Do not use the machine on a paved area that has
been graveled where discharged material may
cause injuries.
앬 Ensure that the loading funnel inlet is empty
before you start the machine.
앬 Keep your head and body away from the infeed
opening.
앬 Do not move your hands, other body parts or
clothing into the infeed chamber, ejector chute or
near other moving parts.
앬 Make sure that you are balanced and standing on
a firm surface at all times. Do not stretch forwards.
Never stand higher than the machine when
feeding material into it.
앬 Keep away from the discharge zone when you
start the machine.
앬 If foreign bodies get into the cutting tool or the
machine generates unusual noises or vibrates in a
strange way, switch off the motor immediately and
To Next Page
Loading...
Need help?
General