·
B.
OPERATIONS
Note:Be sure to read this chapter referring to the front diagrams
of
chapter
"2.
CONTROLS" on page 3 (unfold).Basic Operations
Be
sure
to
lower
the
volume
before
switching
off
the
unit
power
or
the
ignition
key. The
unit
remembers
its
last
volume
setting.
If
you
switch
the
power
off
with
the
volume
up, when
you
switch
the
power
back
on,
the
sudden
loud
volume
may
hurt
your
hearing and damage
the
unit.
Turning
on/oft
the
power
Note:
• Be careful about using this unit for a long time
without running the engine.
If
you drain the car's
battery too
far,
you
may
not
be
able to start the
engine
and
this can reduce the service life
of
the
battery.
1. Press the [SRC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the
[SRC] button for 1 second
or longer to turn off the power for the unit.
Selecting a mode
1.
Press the [SRC] button to change the
operation mode.
2. Each time you press the
[SRC] button, the
operation mode changes in the following
order:
Radio mode
~
CD mode
~
Radio mode...
Note:
•
If
the CD mode is selected when no disc is
inserted, the display shows "NO DISC".
Adjusting
the volume
Turning the [ROTARY] knob clockwise
increases the volume; turning it
counterclockwise decreases the volume.
*The volume level
is
from 0 (minimum)
to
33
(maximum).
Switching the
display
Press the [D] button to select the desired display.
Each time you press the [D] button, the display
switches
in
the following order:
Main display
~
Clock display
~
Main display...
Setting the Z-Enhancer
This unit are provided with 3 types of sound tone
effects stored
in
memory.
Select the one
you
prefer.
*The factory default setting
is
''Z-EHCR OFF".
1.
Each time you press the [Z] button, the tone
effect changes
in
the following order:
"Z-ENHANCER 1" (bass emphasized)
~
"Z-ENHANCER 2" (treble emphasized)
~
"Z-ENHANCER 3" (bass and treble
emphasized)
~
"Z-EHCR OFF" (no sound
effect)
~
"Z-ENHANCER 1"...
Audio
Mode Adjustments
1. Press the [A-M] button to select the
adjustment mode. The mode switches as
follows each time the
[A-M] button is pressed:
BASS
~
TREB
~
BAL
~
FAD
~
Previous
mode
*When the Z-Enhancer function is turned
on
BASS (bass) and TRE (treble) cannot
be
'
selected.
2. Turning the
[ROTARY] knob to adjust the
selected audio mode.
BASS (bass): Adjustment range:
-7
to
+7
TREB (treble): Adjustment range:
-7
to
+7
BAL
(balnce): Adjustment range: L13 to R 13
FAD (fader): Adjustment range: F12 to R12
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
*The display returns
to
the previous mode 7
seconds after the adjustment.
Adjusting
MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust the
low sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
*The factory default setting
is
off.
1. Press the
[M-B] button to turn
on
or off the
MAGNA BASS EXTEND effect.
"M-B EX"
lights
in
the display
on
or off.
Turning the screen saver function
on
or
oft
This unit is provided with the screen saver
function.
8
08165
To Next Page
Loading...
Need help?
General
