Basic Operations
You
can turn on or off this function.
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
*The factory default setting is on.
1.
Press and hold the [0] button for 1 second or
longer to switch to the adjustment selection
display.
2.
Press the [
...
~]
or
[~]
button to select
"SCRNSVR".
3. Turn the [ROTARY] knob to select the
setting. Each time you turn the [ROTARY]
knob, the setting changes
in
the following
order:
SSOFF
....
SSON
4.
Press the [0] button to return to the previous
mode.
Setting the
Clock
1.
Press and hold the [0] button for 1 second or
longer to switch to the adjustment selection
display.
2.
Press the
[~]
or
[~]
button to select
"CLOCK <E>".
3.
Press the
[~II]
button.
4.
Press the [
...
~]
or
[~]
button to select the
hour or the minute.
5.
Turn the [ROTARY] knob to set the correct
time.
* The clock is displayed
in
12-hour format.
6.
Press the
[~II]
button to store the time into
memory.
7.
Press the [0] button to return to the previous
mode.
Note:
•
If
you
select
another
operation
mode
while
you
are
setting the clock, the
clock
setting operation
will
be
canceled.
•
If
you
remove the vehicle's
battery
for a
check
or
repair, the
clock
will
be
reset, so
you
must
set
it
again.
Illumination
dimmer
function
When the illumination line of this unit is
connected with the car-side illumination signal
line, the display illumination of this unit dims in
connection with turning on the car-side
illumination.
Radio Operations
Listening to the radio
1.
Press the [SRC] button and select the radio
mode. The frequency appears
in
the display.
2.
Press the [BND] button and select the radio
band. Each time the button is pressed, the
radio reception band changes
in
the following
order:
F1
(FM1)
...
F2
(FM2)
...
F3
(FM3)
...
AM
...
F1
(FM1)
...
3.
Press the
[~]
or
[~]
button to tune
in
the
desired station.
Seek tuning
1.
Press the [BND] button and select the
desired band.
*If "MANU" is lit
in
the display, press and hold
the [BND] button for 1 second or longer.
"MANU"
in
the display goes off and seek
tuning is now available.
2.
Press the
[~]
or
[~]
button to
automatically seek a station.
When the
[~]
button
is
pressed, the station
is
sought
in
the direction of higher frequencies; if
the
[~]
button
is
pressed, the station
is
sought
in
the direction of lower frequencies.
Manual tuning
1.
Press
the
[BND] button and select the
desired band.
*If "MANU" is not lit
in
the display, press and
hold the [BND] button for 1 second or longer.
"MANU" is lit
in
the display and manual tuning
is now available.
2.
Press the
[~]
or
[~]
button to manually
tune
in
a station.
Recalling a
preset
station
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exist to store individual radio
stations
in
memory. Pressing the corresponding
[DIRECT] button recalls the stored radio
frequency automatically.
1.
Press the [BND] button and select the
desired band.
2.
Press the corresponding [DIRECT] button to
recall the stored station.
* Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store that station
into preset memory.
08165
9
To Next Page
Loading...
Need help?
General
