Craftsman CMCCS320D1 User Manual

ENGLISH
16
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer SafetyAct.
• Register online at www.craftsman.com/registration
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a CRAFTSMAN factory service center
or a CRAFTSMAN authorized service center. Always use
identical replacementparts.
IMPORTANT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.
1. Turn tool off, remove the battery pack and
removeaccessories.
2. Install guide bar scabbard
10
onto the guide bar
4
.

CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
theVersatrack™Trackwall.
3. Flip or pull open the integral hang hook
26
. It clicks
when locked intoposition.
4. Mount the integral hang hook to the
Versatrack™Trackwall.
NOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Versatrack™ (Fig. S)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑upcan causeinjury.

WARNING: To reduce the risk of serious personal injury,
do not use a damaged Versatrack™ integral hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
integral hang hook or Versatrack™ Trackwall will not
support the weight of thetool.

WARNING: To reduce the risk of serious personal injury,
DO NOT suspend tool overhead or suspend objects
from the integral hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the integral hanghook.

WARNING: The Versatrack™ integral hang hook
is intended to mount the tool onto a Versatrack™
Trackwall rail. Do not use the integral hang hook to
mount the tool to any othersurface.

WARNING: The Versatrack™ integral hang hook is not
a belthook.

WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to not
exceed 75lb (35 kg) per linearfoot.

WARNING: Before using the tool make sure that
the Versatrack™ integral hang hook is returned to its
originalposition.
It is recommended that a saw chain be sharpened no more
than fourtimes.
NOTE: The cutters will dull immediately if they touch the
ground/dirt or a nail whilecutting.
To get the best possible performance from your pruner it is
important to keep the teeth of the saw chain sharp. Follow
these helpful tips for proper saw chain sharpening:
1. For best results use a 11/64" (4.5mm) file and a file holder
or filing guide to sharpen your saw chain. This will ensure
you always get the correct sharpeningangles.
2. Place the file holder flat on the top plate and depth
gauge of thecutter.
3. Keep the correct top plate
25
filing angle line of 30° on
your file guide parallel with your chain (file at 60° from
chain viewed from the side) as shownin Fig. P.
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of thechain.
NOTE: Use a flat file to file the tops of the rakers (portion
of chain link in front of the cutter) so they are about .025"
(.635 mm) below the tips of the cutters as shownin Fig. Q.
5. Keep all cutter lengthsequal as shownin Fig. R.
6. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
isremoved.

CAUTION: After filing, the cutter will be sharp, use
extra caution during thisprocess.

Craftsman CMCCS320D1 Specifications

General

Brand	Craftsman
Model	CMCCS320D1
Category	Chainsaw
Language	English