Crestron AMP-150-70 User Manual

DO GUIDE
AMP-225/AMP-150-70/AMP-150-100/AMP-1200-70/AMP-1200-100/
AMP-2100/AMP-2100-70/AMP-2100-100
Modular Ampliers
The Modular Amplier Series can be congured for individual module use on a at surface or using
the “slide-lock” system, ganged together (one or more modules) for installation in a 1RU rack space.
The ampliers are functionally similar to each other with varying capabilities. For simplicity within this
guide, the term “amplier” is used except where noted.
DO Assemble the Device
If a single amplier is to be used on a at surface, refer to “Placing on a Flat Surface.” Otherwise,
continue below for instructions on creating an amplier assembly that can be placed in a standard
equipment rack. The only tools needed are a #1 or # 2 Phillips screwdriver, and a 1/4" nutdriver.
Gang Ampliers Together
Perform the following procedure to gang ampliers together. Refer to the diagrams.
1. Remove the two screws securing the rail to the amplier.
2. Remove the rail from unit 1 by sliding it off the side of the amplier.
3. Attach the rail to unit 2 using the three supplied at head screws.
4. Slide unit 1 into unit 2 assembly.
5. Secure unit 1 to unit 2 assembly with two of the screws removed in step 1.
6. Repeat steps 1 through 5 for additional ampliers.
Congure for Rack Installation
Before an amplier can be installed in a rack, additional hardware must be installed.
Faceplates
If an amplier or group of ampliers are not wide enough to mount in a rack, faceplates can be
assembled to “widen” the amplier to t in the rack. Create a faceplate by attaching an extrusion
plate to a quarter-width or half-width rack ear, as shown in the following diagrams. Secure the
extrusion plate to the rack ear using a 1/4" nutdriver and the included nuts.
Attach Rack Ears to Ampliers
Attach the faceplate bracket(s) or rack ears as required to the amplier(s). Refer to the following
diagram for details.
NOTE: Faceplates should not be attached to rack ears that are attached to the length of the
amplier.
DO Install the Device
Once assembled, the amplier can be mounted into a rack, mounted onto a at surface, or placed
onto a at surface.
Mounting into a Rack
Each amplier occupies 1U of rack space. Using a #1 or #2 Phillips screwdriver, mount the device into
the rack using four mounting screws (not included).
WARNING: To prevent bodily injury when mounting or servicing this unit in a rack, observe the
following guidelines:
• When mounting this unit in a partially lled rack, load the rack from the bottom to the top with
the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.
CAUTION: To prevent equipment damage, use only the Crestron rack ears provided for this device.
NOTE: Although ampliers can be installed in a rack without space between them, it is
recommended to add a space between devices to allow ease of access to the rear panel
connections.
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Power Cord, 6' 7" (2 m) 20 01134
1 Connector, 5-Pin 2003577
1 Extrusion Plate, Quarter-Width 4525244
1 Extrusion Plate, Half-Width 4525245
1 Quarter-Width Rack Ear, 1U 2046651
1 Half-Width Rack Ear, 1U 2046652
2 Bracket, Wall Mount 2046992
4 Nut, 04-40, Keps 2004878
6 Screw, 6-32 x 3/8", Undercut Head, Phillips Black 2007235
4 Foot, 0.5" x 0.5" x 0.23", Adhesive Black 2002389
For AMP-150 -70, AMP-150-10 0, AMP-1200-70, AMP-120 0-100
1 Connector, 2-Pin 2044402
For AMP-225, AMP-2100, AMP-2100-70, AMP-2100-100
2 Connector, 2-Pin 2044402
Remove these
screws.
Unit 1
Rail
Unit 2
Rail
Unit 1
Unit 2 assembly
Quarter-size faceplate bracket Half-size faceplate bracket
Quarter-size rack ear
(no faceplate attached)
Half-size faceplate bracket
Unit 1
Unit 2 assembly

Crestron AMP-150-70 Specifications

General

Brand	Crestron
Model	AMP-150-70
Category	Amplifier
Language	English