Name: Crestron CCS-UC-300
Brand: Crestron
Rating: 4 (1 reviews)

To Previous Page

DO GUIDE

DOC. 7960D (2048281) 08.17

Specications subject to change without notice.

DO Connect the Device

Make connections to the front and rear of the engine. Connect power last.

NOTE: Ensure the unit is properly grounded by connecting the chassis ground lug to an earth ground (building steel).

Hardware Hookup Front

Hardware Hookup Rear

DO Secure the Cables

1. Use a #1 Phillips screwdriver to remove the two screws adjacent to the DOCK CONNECTIONS - 1 port.

2. Slide the cable retention bracket over the cable connected to the DOCK CONNECTIONS - 1 port as shown in the following diagram.

3. Secure the cable retention bracket to the engine using the two screws removed in step 1.

4. Use the included tie wraps to secure all the cables connected to the rear of the engine to the cable retention plate.

DO Congure the Device

For details on conguring the device, refer to the CCS-UC-300 Supplemental Guide (Doc. 7961) at www.crestron.com/manuals.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL

Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

この装置は、クラスB情報技術装置です。この装置は、家庭環境で使用することを目的としています力くこの装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さ

い。

This is a class B product based on the standard of the VCCI Council. If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the

equipment according to the instruction manual.

仅适用于海拔2000m以下地区安全使用”或类似的警告语句

Used only at altitudes not more than 2000m above sea level.

仅适用于非热带气候条件下安全使用”或类似的警告语句

Used only in nontropical conditions

Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and

end-users under a separate End-User License Agreement. Both of these Agreements can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.

The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.

Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, Cresnet, DM, and DM 8G+are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries.

Microsoft Surface and Skype are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. PL ASTITE is either a trademark or registered trademark of Research Engineering & Manufacturing, Inc. in the United States and/or other countries.

UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

DO Learn More