12 se c t i O n 4 — cO n t r O l s & fe a t u r e s
Forward Drive Pedal
The forward drive pedal is located on the right side
of the tractor, along the running board. Press the
drive pedal forward to cause the tractor to travel
forward. Ground speed is also controlled with
the drive pedal. The further forward the pedal is
pivoted, the faster the tractor will travel. The pedal
will return to its original position when it’s not
pressed.
Reverse Pedal
The reverse drive pedal is located on the right side of
the tractor along the running board. Ground speed
is also controlled with the reverse pedal. The further
downward the pedal is pivoted, the faster the tractor
will travel. The pedal will return to its original position
when it’s not pressed.
PTO/Blade Engage Lever
Activating the PTO engages power to the cutting
deck or other (separately available) attachments.
Lift up on the PTO/Blade Engage lever to activate
it. Push down on the PTO/ Blade Engage lever to
disengage the power to the cutting deck or other
(separately available) attachments.
NOTE: The PTO/Blade Engage lever must be in
the disengaged (OFF) position when starting the
engine.
Parking Brake/Cruise Control Lever
The parking brake/cruise control lever is located
on the left of the tractor’s dash panel. It is used
to engage the parking brake when the tractor is
at rest. Engaging the lever while the tractor is in
motion allows the tractor to remain at a constant
ground speed without applying pressure to the
forward drive pedal. Refer to the Operation section
of this manual for detailed instructions regarding
the parking brake as well as the cruise control
feature.
NOTE: Cruise control can NOT be engaged at the
tractor’s fastest ground speed. If the operator should attempt
to do so, the tractor will automatically decelerate to the fastest
optimal mowing ground speed
NOTE: The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut off.
WARNING! Never leave a running machine
unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
Manual Lift Lever (If so equipped)
LO
2
3
4
5
6
7
8
9
10
1 1
12
HI
The lift lever is located in the right fender and is used to raise
and lower the deck. Pull the handle to the left out of the index
notch and push downward to lower the deck, or pull upward to
raise the deck. When the desired height is attained, move the lift
handle to the right until fully in the index notch.
Electric Lift Switch (If so equipped)
E L ECTRIC
DECK
LI
FT
R AIS E
DECK
LO W
ER
DECK
T o
Oper
a t e
El ect r i
c Deck
Lif t
Height
A
dj ust ment
Raise
El ect r i
c Deck
Lif t
T o
Th e
Highe
st
Po sition.
Set
Cut ting
Height.
Lo wer
El ect r i
c Deck
Lif t
T o
Chosen
Cut ting
Po sition.
The electric lift switch located in the right fender and is used to
raise and lower the deck. To lower the deck press down on the
front of the switch and to raise the deck push down on the rear of
the switch.
Cutting Height Lever (If so equipped)
LO 1 2 3 4 5 HI
The cutting height lever is used to set the distance the deck can
be lowered. The cutting height lever can be set to six different
positions by moving the lever up or down to the desired setting.
Ignition Switch Module
WARNING! Never leave a running machine
unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting.
To start the engine, insert the key
into the ignition switch and turn
clockwise to the START position.
Release the key into the NORMAL
MOWING MODE position once
the engine has fired.
To stop the engine, turn the
ignition key counterclockwise to
the STOP position.
CAUTION: Prior to
operating the tractor, refer to both Safety Interlock
Switches and Starting The Engine in the Operation
section of this manual for detailed instructions
regarding the Ignition Switch Module and operating
the tractor in REVERSE CAUTION MODE .
R
To Next Page
Loading...
Need help?
General