Delta DVP-ES2 Instruction Sheet

- 2 -
Model
name
16ES2
00R/T
24ES2
00R/T
32ES2
00R/T
40ES2
00R/T
40ES2
00RM
58ES2
00R/T
60ES2
00R/T
80ES2
00R/T
20EX2
00R/T
32ES2
11T
L 105 125 145 165 165 225 225
302
145 145
L1 97 117 137 157 157 217 217
294
137 137
WT
R
377g 414g 489g 554g 562g 705g 696g 890g 462g －
T 351g 387g 432g 498g － 622g 614g 785g 442g 321g
Model
name
20ES2
00RE/
TE
32ES2
00RE/
TE
40ES2
00RE/
TE
60ES2
00RE/
TE
L 125 165 194 255
L1 117 157 186 247
WT
RE 453g 569g 630g 787g
TE 416g 520g 574g 704g
 Electrical Specifications
Model
Item
32ES211T All ES2 models except for 32ES211T
Power supply
voltage
24VDC(-15~+20%) 100 ~ 240VAC (-15% ~ 10%); 50 / 60Hz  5%
Connector European standard removable terminal block (Pin pitch: 5mm)
Operation
ES
200
DVP-ES2 starts to run when the power rises to 95 ~ 100VAC and stops
when the power drops to 70VAC. If the power is suddenly cut off, the PLC
will continue running for 10ms.
ES
211
DVP-ES2 starts to run when the power rises to 20.4VDC~28.8VDC and
stops when the power drops to 17.5VDC. If the power is suddenly cut off,
the PLC will continue running for 10ms.
Power supply
fuse
2.5A / 30VDC, Polyswitch 2A / 250VAC
Power
1.8W 30VA
DC24V current
output*1
－ 500mA
Power supply
－ DC24V output short circuit protection
Voltage
withstand
1,500VAC (Primary-secondary), 1,500VAC (Primary-PE),
500VAC (Secondary-PE)
Insulation
> 5MΩ at 500VDC (between all I/O points and ground)
Noise immunity
ESD (IEC 61131-2, IEC 61000-4-2): 8kV Air Discharge
EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2kV, Digital I/O: 1kV, Analog &
Communication I/O: 1kV
RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
Grounding
The diameter of grounding wire shall not be less than that of L, N terminal of
the power supply. (When many PLCs are in use at the same time, please
make sure every PLC is properly grounded.)
Environment
Operation: 0°C~55°C (temperature), 5~95% (humidity), pollution degree 2
Storage: -25°C~70°C (temperature), 5~95% (humidity)
Agency
approvals
UL508, European community EMC Directive 89/336/EEC and Low Voltage
Directive 73/23/EEC
Vibration/shock
immunity
International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 &
IEC 68-2-27 (TEST Ea)
*1: It is suggested that the power output should not be supplied to HMIs.

Delta DVP-ES2 Specifications

General

Brand	Delta
Model	DVP-ES2
Category	Controller
Language	English