Denon AVR-1912 Getting Started

5
Preparation Playback
ENGliShDEutSchFrANçAiSitAliANoESpAñolNEDErlANDSSVENSKA
РУССКИЙPOLSKITÜRKÇE
Setup Wizard
Basic operation of Setup Wizard
Move to the item that
you want to configure
using ui.
Please select the
speaker configuration
to be used.
5.1ch
7.1ch
Others
7.1ch adds 2 more
speakers to 5.1ch, for
enhanced surround.
Speaker Connection
Move to the item that
you want to configure
using o p.
Speaker Connection
7.1ch is selected for speaker
system. Select “Yes” to confirm.
Yes No
Enters the selection.
Please connect the
speakers.
Location :CENTER
Terminal
:CENTER
Press [ENTER] for next
connection.
Ready to connect
Speaker Connection
Returns to the start of
each setting.
or
Cancels the Setup
Wizard.
Do you wish to stop
and exit wizard?
You can restart the
setup wizard anytime
using the on screen
menu.
Setup Wizard
Yes
No
Getting Started
Insert the main unit power plug into the wall
socket.
To household power outlet
(AC 230 V, 50/60 Hz)
Power cord
(Supplied)
Press ZONE SELECT to switch the zone mode to J
(MAIN ZONE).
Switch the zone mode
J
Lights
•This remote control can be operated in two separate zones, MAIN
ZONE and ZONE2.
•Set the remote control to MAIN ZONE to operate the Setup
Wizard.
1
2
Press AMP to set the remote control unit to AMP-
operation mode.
Switch the AMP-operation mode
•This remote control is a preset remote control that can be used to
control connected devices.
Press ON ( Z ) on this unit.
The power switches on, and the Setup Wizard start screen is
displayed on the television screen.
Power on
1. Language Select
2. Speaker Connection
3. Speaker Calibration
4. Source Setup
5. Remote Setup
6. Network Setup
Complete
This wizard assists
connection and setup
of receiver step by
step. You can skip or
cancel each section if
necessary. Press [ENTER]
on remote to start.
START
Setup Wizard
Press ENTER.
Start the Setup Wizard.
Setup Wizard has started.
Please follow the message on screen.
To start the Setup Wizard again after exiting it, select “Setup
Wizard” in the menu (vm page 70 “Menu map”).
3
4
5
When power is switched to standby
Press STANDBY (X).
GPower indicator status in standby modeH
•Normal standby : Off
•When “HDMI Control”(vm page 86) is
set to “ON” : Red
NOTE
During power standby, a minimal amount of power is consumed. To
totally cut off the power, remove the power cord from the power
outlet.
Australia model
Europe model

Denon AVR-1912 Specifications

General

Impedance	47 Ω
Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	125 W
Power output per channel (20-20KHz@8 Ohm)	90 W
HDMI in	6
Composite video in	3
Component video (YPbPr/YCbCr) in	1
Headphone connectivity	6.3 mm
Connectivity technology	Wired
Speakers connectivity type	Banana connector/Binding posts
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
Ethernet LAN	Yes
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	56
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL
Display	-
Product color	Black
Audio decoders	Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD
Apple docking compatibility	iPhone, iPod
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	460 W

Weight and Dimensions

Depth	382 mm
Width	435 mm
Height	167 mm
Weight	10200 g