Denon AVR-750 User Manual

Operating Possible in the Various Surround Modes
The folowing is a list of the buttons and functions which can be operated during the different surround modes. Figures In parentheses
indicate adjustment ranges.
DOLBY PRO LOGIC
CONCERT HALL
"1 Switches to the Dolby Pro Logic from any modes other than Dolby Pro Logic.
‘The level of the center and surround (rear) channels can be adjusted by 2 dB step.
The delay time can be set by 1.5 ms step.
* The sound may be distorted for some sources if the surround (rear) level is raised during surround playback.
if this happens, lower the surround (rear) level.
[5] USTENING TO THE RADIO
To know the tuning frequency steps, see the Table of Tuning Frequency Steps.
5-1 Setting the frequency step
(AVR-750/770)
‘AM SPACING
=a
®
The tuni
disconnect the
TABLE OF TUNING FREQUENCY STEPS
frequency steps are switchable between 9 kHz and 10 kHz for AM,
between 0.05 MHz and 0.2 MHz for FM. To switch the tuning frequency steps,
power plug and set the AM SPACING switch (®) on the rear panel to
the desired position. Then plug in the AC mains again.
5-2 Auto preset memory
This unit is equipped with a function for automatically searching
for FM broadcast stations and storing them in the preset memory.
@ Tum on the unit while holding in the MEMORY button. The
unit automatically begins searching for FM broadcast stations.
@ ON/ STANDBY & OFF
@ When the first FM broadcast station is found, that station is
Stored in the preset memory at channel A1, Subsequent
Stations are automatically stored in order at preset channels
A2 to A8, B1 to B8, C1 to C8, D1 to D8 and Et to E8, fora
maximum of 40 stations.
5-3 Auto tuning
@ Set the input function to "TUNER®.
—— Frction
youn co TUNER
@ Watching the display, press the BAND button to select the
desired band (AM or FM).
— TUNER
MODE BAND
© Press the MODE button to set the auto tuning mode.
= TUNER
MODE BAND
“AUTO* appears on the display.
12
© Channel A1 is tuned in after the auto preset memory
operation is completed.
NOTES:
© fan FM station cannot be preset automatically due to poor
reception, use the “Manual tuning" operation to tune in the station,
then preset it using the manual “Preset memory” operation.
* To interrupt this function, press the POWER operation button.
© Press the TUNING UP or DOWN button.
Automatic searching begins, then stops when a station is tuned in.
Ht tuning does not stop at the dasired station, use to the *Manual
tuning” operation.
5-4 Manual tuning
© Set the input function to "TUNER".
© Watching the dispiay, press the BAND button to select the
desired band (AM or FM).
© Press the MODE button to set the manuaktuning mode.
Check that the display's “AUTO” indicator turns off.
NOTES:
* When in the auto tuning mode on the FM band, the "STEREO" indicator lights on the display when a stereo broadcasts tuned In. At open
frequencies, the noise is muted and the ‘TUNED and “STEREO? indicators tum off.
* When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the “STEREO*® Indicator tums off.
@ Press the TUNING UP or DOWN button to tune in the desired
station.
The frequency changes continuously when the button is held
In.
5-5 Preset memory
© Use the "Auto tuning’ or "Manual tuning" operation to tune in
the station to be preset in the memory.
@ Press the MEMORY button.
ey
BAND MEMORY
Itsy,
© Press the SHIFT button and select the desired memory block
{A to E).
oe TUNING PRESET ony
SHOT OWN O
@ Press the PRESET UP or DOWN button to select the desired BAND MEMORY
preset channel {1 to 8).
[7 TUNIC PRESET manny
rT DOWN we
O Ok
5-6 Recalling preset stations
© Watching the display, press the SHIFT button to select the
preset memory block.
[ose TUNING PRESET comeny SHIET
@ Watching the display, press the PRESET UP or DOWN button
to select the desired preset channet.
SoA
{6] INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normai or when the
operation of the unit dees not shows the reasonable result, the
initialization of the microprocessor is required by the following
procedure.
© Switch off the unit using the main unit's POWER operation
switch,
@ Hold the following TUNER button and VIDEO SELECT button,
and tum the main unit's POWER operation switch on.
© Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 buttons.
© Switch on the unit and the microprocessor will be initialized.
© Press the MEMORY button again to store the station in the
preset memory.
To preset other channels, repeat steps @ to @.
A total of 40 broadcast stations can be preset — 8 stations
(channels t to 8) In each of blocks A to E.
NOTE:
+ When the microprocessor is reset, all the settings you have made are reset to the values set upon shipment from the factory.
13
:
:

Denon AVR-750 Specifications

General

Brand	Denon
Model	AVR-750
Category	Stereo Receiver
Language	English