22
ENGLISH
15
PRESET
1. Preset mode
q The preset mode is available when PRESET button is pushed for more than 1 sec while DN-D9000 is in
Cue, pause or no disc mode.
w Turn the PARAMETERS knob to select the preset item.
e After selecting an item, push the PARAMETERS knob to select the preset data.
r To change other Preset items, repeat these steps.
t Push the PRESET, CUE or PLAY/PAUSE button to exit from the Preset mode.
2. Preset items and data
The “*” mark next to the data indicates the default value.
(1) AUTO CUE: Auto Cue level search on/off.
ON* / OFF
(2) PITCH RANGE: Select the playing pitch range when the power is turned on.
±4 / ±10* /±16 / ±24%
(3) ALPHA-TRACK OUTPUT: Alpha-Track playback output destination.
Main out* / Monitor out
(4) AUTO CLOSE: Time for automatically closing disc holder.
OFF / 10 / 30* / 60 seconds
(5) EOM: Track end message start time.
OFF / 10* / 15 / 20 / 30 / 60 / 90 seconds
(6) Alpha-Track FADER START: Select the Alpha-Track fader Start ON/OFF.
ON / OFF*
(7) FADER: Select 2-line type (Cue and Play) or 1 line type (Play and Pause).
PLAY/CUE* / PLAY/PAUSE
(8) POWER ON PLAY: Playback starts when the power is turned on if a disc is loaded.
ON / OFF*
(9) A3/4 MODE: Select the A3 and A4 button operating modes when the power is turned on.
Sampler* / 4H/S / Alpha-Track H/S
(10) SINGLE/CONTINUOUS: Select the play mode when the power is turned on.
SINGLE* / CONTINUOUS
(11) ELAPSED/REMAIN: Select the time mode when the power is turned on.
ELAPSED* / REMAIN
(12) PROGRAM ALL CLEAR: Clear all program play data in the non-volatile memory.
NOTE: This Preset item can be only performed in CD1 (left side) of the remote controller.
q To clear the program, push the PARAMETERS knob and select “YES“.
•“Clear OK?” flashes on the character display.
w Push the PARAMETERS knob again and select “OK” to execute clearing the program.
“Prog. Clear” is displayed on the character display while data clearing.
e Once clearing is completed, “Complete!” is displayed.
(13) MEMO ALL CLEAR: Clear all MEMO data in the non-volatile memory.
NOTE: This Preset item can be only performed in CD1 (left side) of the remote controller.
q To clear all MEMO data, push the PARAMETERS knob and select “YES”.
•“Clear OK?” flashes on the character display.
w Push the PARAMETERS knob again and select “OK” to execute clearing all MEMO data.
•“Memo Clear” is displayed on the character display while clearing.
e Once clearing is completed, “Complete!” is displayed.
(14) MEMO ALL COPY: Copy all MEMO data from the master unit of DN-D9000 (or DN-2600F) to the slave
unit of DN-D9000 when both unit are connected by the specified Cross Cable. (See
diagram for the cable.)
NOTE: This Preset item can be only performed in CD1 (left side) of the remote controller.
Also, be sure that both disc trays are open, or both have no discs inside.
A cross cable used:
• Using the cross cable, connect the X-EFFECT terminals between two DN-D9000 units or
between one DN-2600F and one DN-D9000 unit.
• If a DN-2600F is the master unit, take the procedures below in the Preset mode of the DN-2600F
beforehand. (For details, refer to the DN-2600F’s operating instructions.)
✽ Set the “Copy Master” for the Preset item (14).
Then, step to the q below on the slave unit of DN-D9000.
• Perform the copying operation as below on the slave unit of DN-D9000.
q To start copying, push the PARAMETERS knob and select “YES”. Now “Copy OK?” messages
flashes on the character display.
w Push the PARAMETERS knob again to confirm. Now “Start OK?” is displayed.
NOTE: If a DN-2600F is the master unit, take the procedures below in the Preset mode of the
DN-2600F here.
In the Preset item (15), first start copying on the DN-2600F. Then, step to e below on the
slave unit of DN-D9000.
e Push the PARAMETERS knob once again, and the unit starts copying when the MEMO data are
received from the master unit. Now “Copying” is displayed.
• If the master unit and the slave unit are not connected properly or the DN-2600F is not
prepared to start sending data, “Not Connect” is displayed on the character display.
r When copying is completed correctly, “Complete!” is displayed.
•“Copy Error” is displayed on the character display if copying was not completed correctly.
In this case, try the above procedure again.
• The copied MEMO data are added to the highest number area of the slave DN-D9000 unit.
(15) PRESET CLEAR: Set all the preset data back to the factory defaults.
q To clear the PRESET data, push the PARAMETERS.
“Initial OK?” flashes on the character display.
w Push the PARAMETERS knob again and select “OK” to start clear the preset data.
“Preset Int” is displayed on the character display while data clearing.
e Once clearing is completed, “Complete!” is displayed.
To Next Page
Loading...
Need help?
General
