EasyManuals Logo
Home>Denon>Amplifier>PMA-1500AE

Denon PMA-1500AE User Manual

Denon PMA-1500AE
18 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
ENGLISH
!5
REC. (REC OUT) terminals
These are playing and recording output terminals for
connection to tape decks.
!6
PRE OUT terminals
Use these when adding a power amplifier, a subwoofer
with built-in power amplifier, etc.
Connect these PRE OUT terminals to the input terminals
on the additional power amplifier, subwoofer, etc.
!7
P. DIRECT ( Power amp direct ) terminals
Source connected to this terminal is directly fed to the
power amplifier set volume level by the component
connected to this terminal.
NOTE:
Signals are outputted from the PRE OUT terminals
even when using headphones.
No signal is outputted when selecting P. DIRECT
terminals.
NOTE:
The PHONO input terminals are equipped with a short
pin-plug. Remove this plug to connect a record player.
Store the removed short pin-plug in a safe place so as
not to lose it.
o
Input indicator
The Indicator for the program source selected with the
INPUT SELECTOR control lights.
!8
SPEAKER SYSTEMS terminals
Connect the speaker systems here.
!9
AC inlet receptacle (AC IN)
Connect the included power supply cord here.
Do not use any other cord than the provided power supply
cord.
@0
SIGNAL GND (ground) terminal
Connect the turntable’s ground wire here.
@1
CARTRIDGE selection switch
This switch is set according to the type of player cartridge
to be used. Set this switch to MM (
£ ) or MC (¢ )
according to the type of cartridge used on your turntable.
NOTE:
This terminal is used to reduce noise when a turntable,
etc., is connected.
It does not provide grounding.
Rear panel
!4
INPUTS terminals
These are INPUTS terminals for CD players, turntables,
AM/FM tuners, tape decks or other playback components.
!1
SOURCE DIRECT
The controls (BASS, TREBLE and BALANCE ) can be used
when this switch is in the OFF (
£) position.
When set to the ON (
¢) position, the above controls are
by-passed and the signals are input directly to the volume
control circuit, providing high quality sound.
!2
POWER indicator
When the POWER switch is turned ON/STANDBY(¢),
the power indicator lights.
Light green : Power is on
Light red : Power is in the standby mode
!3
Remote control sensor
This sensor receives the infra-red light transmitted from
the wireless remote control unit.
For remote control, point the wireless remote control unit
towards the sensor.
NOTE:
When selecting the P. DIRECT terminal, volume control
function of this unit does not work, so set volume level
by the component connecting to this terminal.
!0
P. DIRECT (Power amp direct) button
ON :
P. DIRECT terminals selected, and input indicator is turned
off.
OFF :
Selected INPUT SELECTOR knob makes program source
play.
NOTE:
When the P. DIRECT button is ON position, Input
indicator dose not light.
5
ENGLISH

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon PMA-1500AE and is the answer not in the manual?

Denon PMA-1500AE Specifications

General IconGeneral
Output level150 mV
Receiver type-
Frequency range20 - 20000 Hz
Audio output channels2.0 channels
Signal-to-Noise Ratio (SNR)108 dB
Total Harmonic Distortion (THD)0.01 %
Dynamic power per channel (4 Ohm)140 W
Power output per channel (20-20KHz@8 Ohm)70 W
Product colorBlack
Bass adjustmentYes
Handheld remote controlNo
Apple docking compatibilityNot supported
AC input voltage230 V
AC input frequency50 Hz
Power consumption (typical)305 W
Weight and Dimensions IconWeight and Dimensions
Depth410 mm
Width434 mm
Height134 mm
Weight14600 g

Related product manuals