DeWalt DCF680G2F-QW Manual

9
ENGLISH
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.
Two Position Screwdriver (Fig.C)
DCF680
To convert the tool to an angled screwdriver press the release
button
10
and rotate the top portion of the tool as shown in
FigureC.
NOTICE: Do not use screwdriver as a pry bar in
eitherposition.

CAUTION: To avoid screwdriver being turned on
accidentally, put the lock off switch
2
in the up,
locked‑off,position.
Torque Adjustment Collar (Fig.A,C)
DCF680
The torque adjustment collar
9
is marked with numbers and
a MAX symbol. To set the torque align the desired setting with
the arrow on the tool housing. The higher the number on
the collar, the higher the torque. To lock the clutch for heavy
fastening operations, move to the MAX position. Failure to do
this will allow the clutch to slip while attempting tofasten.
Prior to Operation
• Make sure your battery pack is (fully)charged.
• Insert the appropriatebit.
Inserting and Removing the Battery Pack
from the Tool (Fig.B)
NOTE: Make sure your battery pack
6
is fullycharged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack
6
with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
1. Press the release button
5
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig.B)
Some DeWALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑userapplication.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can causeinjury.

WARNING: Use only DeWALT battery packs andchargers.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Quick Release Chuck (Fig.A,D)
NOTE: The chuck accepts 6.35mm hex accessoriesonly.
To install a bit, insert the bit into the chuck until the clip locks it
inplace.
To remove a bit, pull the chuck collar
8
forward. Remove the bit
and release thecollar.
DCF680
Proper hand position requires one hand on the main handle as
shown in FigureE1.

WARNING: If the tool will be used in elongate position
and highest MR please hold tool with both hands as
shown in FigureE2.
DCF682
Proper hand position requires two hand on the tool as shown
in FigureE3.
Screwdriving (Fig.A,E)
Your screwdriver uses gyroscopic technology to sense your
hand motion. To operate, press in the motion control activation
trigger and turn your hand in the direction that you want the
screwdriver tooperate.
Setting Initial Starting Point
1. Grasp the screwdriver as shown in FigureE.
2. Press and hold in the motion control activationtrigger.
3. When the LED illuminates the tool is ready foruse.

DeWalt DCF680G2F-QW Specifications

General

Brand	DeWalt
Model	DCF680G2F-QW
Category	Power Screwdriver
Language	English