DeWalt DCG413N User Manual

8
ENGLISH
cut-off wheel. Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may cause them
toshatter.
e ) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel. Proper wheel
flanges support the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels may be different from
grinding wheelflanges.
f ) Do not use worn down wheels from larger power tools. A
wheel intended for larger power tool is not suitable for the higher
speed of a smaller tool and mayburst.
g ) When using dual purpose wheels always use the correct
guard for the application being performed. Failure to use the
correct guard may not provide the desired level of guarding, which
could lead to seriousinjury.
Additional Safety Warnings Specific for Cutting-Off
Operations
a ) Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and susceptibility
to twisting or binding of the wheel in the cut and the possibility of
kickback or wheelbreakage.
b ) Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operations, is
moving away from your body, the possible kickback may propel
the spinning wheel and the power tool directly atyou.
c ) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheelbinding.
d ) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut. The wheel may bind, walk up or kickback if the power tool is
restarted in theworkpiece.
e ) Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large workpieces
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of the
workpiece on both sides of thewheel.
f ) Use extra caution when making a “pocket cut” into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that can
causekickback.
g ) Do not attempt to do curved cutting. Overstressing the
wheel increases the loading and susceptibility to twisting or binding
of the wheel in the cut and the possibility of kickback or wheel
breakage, which can lead to seriousinjury.
Additional Safety Instructions for
Sanding Operations
a ) Use proper sized sanding disk paper. Follow
manufacturers recommendations, when selecting sanding
paper. Larger sanding paper extending too far beyond the sanding
pad presents a laceration hazard and may cause snagging, tearing
of the disc orkickback.
Additional Safety Instructions for Wire Brushing
Operations
a ) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can easily
penetrate light clothing and/orskin.
b ) If the use of a guard is specified for wire brushing, do not
allow any interference of the wire wheel or brush with the
guard. Wire wheel or brush may expand in diameter due to work
and centrifugalforces.
Additional Safety Rules for Grinders
a ) Do not use Type 11(flaring cup) wheels on this tool.
Using inappropriate accessories can result ininjury.
b ) Always use side handle. Tighten the handle securely. The
side handle should always be used to maintain control of the tool
at alltimes.
c ) When using segmented diamond wheels, use only
diamond wheels with a peripheral gap not greater than
10mm and negative rakeangle (refer to Additional
Information for Guards and AccessoriesChart.)
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot duringoperation.
• Risk of personal injury due to prolongeduse.
• Risk of dust from hazardoussubstances.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
Your DeWALT charger is double insulated in
accordance with EN60335; therefore no earth wire
isrequired.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the DeWALT
serviceorganisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the oldplug.
• Connect the brown lead to the live terminal in theplug.
• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the
earthterminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1mm
2
; the maximum length is30m.
When using a cable reel, always unwind the cablecompletely.
SAVE THESE INSTRUCTIONS
Battery Type
The DCG406, DCG413 operates on an 18V batterypack.

DeWalt DCG413N Specifications

General

Brand	DeWalt
Model	DCG413N
Category	Grinder
Language	English