DeWalt DCH273P2 User Manual

9
English
other voltage. This does not apply to the
vehicularcharger.
SAVE THESE INSTRUCTIONS
Chargers
The DCB105, DCB107, DCB112, DCB113 and
DCB115 chargers accept 10.8V, 14.4V and 18V
Li-Ion XR (DCB123, DCB127, DCB140, DCB141,
DCB142, DCB143, DCB144, DCB145, DCB180,
DCB181, DCB182, DCB183, DCB183B, DCB184,
DCB184B and DCB185) battery packs.
DeWALT
chargers require no adjustment and are
designed to be as easy as possible tooperate.
Charging Procedure (Fig.3)
1. Plug the charger into an appropriate outlet
before inserting batterypack.
2. Insert the battery pack(F) into the charger.
The red (charging) light will blink continuously
indicating that the charging process hasstarted.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in thecharger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
firstuse.
Charging Process
Refer to the table below for the charge status of the
battery pack.
Charge indicators: DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
Charge indicators: DCB107, DCB112, DCB113, DCB115
charging
fully charged
hot/cold pack delay*
* DCB107, DCB112, DCB113, DCB115: The red
light will continue to blink, but a yellow indicator
light will be illuminated during this operation.
Once the battery has reached an appropriate
temperature, the yellow light will turn off and the
charger will resume the charging procedure.
there is no battery pack in the cavity.
Unplug charger before attempting
toclean.
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to worktogether.
• These chargers are not intended for
any uses other than charging
DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock
orelectrocution.
• Do not expose charger to rain orsnow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug andcord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage orstress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, orelectrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of thehousing.
• Do not operate charger with damaged cord
or plug — have them replacedimmediately.
• Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
servicecentre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution
orfire.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent anyhazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce thisrisk.
• NEVER attempt to connect 2 chargerstogether.
• The charger is designed to operate on
standard 230V household electrical
power. Do not attempt to use it on any

DeWalt DCH273P2 Specifications

General

Brand	DeWalt
Model	DCH273P2
Category	Rotary Hammer
Language	English