DeWalt DCH274 Instruction Manual

ENGLISH
7
Accessories

WARNING: Since accessories, other than those offered by
DeWALT, have not been tested with this product, use of such
accessories with this product could be hazardous. To reduce
the risk of injury, only DeWALT recommended accessories
should be used with thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1approved eye protection when
performingthisprocedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any part
of the tool into aliquid.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
causeinjury.
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regularcleaning.
Three-Year Limited Warranty
For warranty terms, go to www.dewalt.com/support/
warranty.
To request a written copy of the warranty terms, contact:
Customer Service at DeWALT Industrial Tool Co., 701East
Joppa Road, Towson, MD 21286or call 1-800-4-DeWALT
(1-800-433-9258).
LATIN AMERICA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warrantyinformation.
FREE WARNING LABEL REPLACEMENT: If your warning
labels become illegible or are missing, call 1-800-4-DeWALT
(1-800-433-9258) for a freereplacement.
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof ofpurchase.
• FOR YOUR SAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer SafetyAct.
Register online at www.dewalt.com/account-login.
Cutting a Hole for an Electrical Outlet (Fig.D)

WARNING: Shut off all live electric circuits to any areas
where cut outs will bemade.
1. Push any wiring deeply into the outlet box to avoid
damage from the cuttingbit.
2. Before hanging the sheet covering the outlet, mark the
approximate location of the center of the outlet on the wall
board. Check the cutting bit depth against the side of the
board to be sure it will cut entirely through thematerial.
3. Tack the sheet in place with a few fasteners, avoiding the
stud holding the outlet. This allows the wall board to flex
slightly around the protruding fixturebox.
4. Turn the cut-out tool on. Holding the tool firmly with
both hands, plunge the bit straight into the center of
theoutlet.
5. Cut to the right until the edge of the box is touched.
Pull out just enough for the bit to clear the edge of the box.
Plunge in again holding the bit gently against the outside
of thebox.
6. Follow the outside of the box as shown keeping slight
pressure against the box. This will minimize wandering and
give you a clean precisecut.
7. Remove the waste and dust from the outlet. Finish
fastening the sheet of wallboard.
• Do not cut material lying on a hard surface. Clearance
behind material to be cut must be allowed for
protrudingbit.
• Disconnect battery from tool before making adjustments,
changing bits, or cleaningtool.
• Do not start the tool with bit engaged in the material. The
bit may grab thematerial.
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacementparts.
service center. If you need assistance in locating any
accessory, please contact DeWALT. Call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com .

DeWalt DCH274 Specifications

General

Brand	DeWalt
Model	DCH274
Category	Cutter
Language	English