DeWalt DCH416 User Manual

ENGLISH
10
DeWALT Tool Tag Ready (Fig. A)
Optional Accessory
Your tool comes with mounting holes
15
and fasteners for
installing a DeWALT Tool Tag. You will need a T20 bit tip to
install the tag. Only use the screws provided. The DeWALT
Tool Tag is designed for tracking and locating professional
power tools, equipment, and machines using the DeWALT
Tool Connect™ app. For proper installation and use of the
DeWALT Tool Tag refer to the DeWALT Tool Tagmanual.
SHOCKS® Active Vibration Control
System
For best vibration control, hold the tool as described in
Proper Hand Position and apply just enough pressure so the
damping device on the main handle is approximately mid
stroke. The hammer only needs enough pressure to engage
the active vibration control. Applying too much pressure will
not make the tool actuate faster and active vibration control
will notengage.
E-Clutch® System (Fig. I)
In addition to the integral (mechanical) clutch, the DeWALT
anti‑rotation E‑Clutch® system, offers technology capable
of detecting the motion of the tool. This feature senses
the motion of the tool and shuts it down if necessary. The
E‑Clutch
®
indicator LED
16
illuminates when the E‑Clutch®
System isengaged.
Your rotary hammer has an E‑Clutch
®
indicator LED
16
,
indicating the E‑Clutch® (ADC) function. Refer to the table for
more information on LEDfunctionality.
Indicator Diagnosis Solution
OFF Tool is
functioning
normally
Follow all warnings and instructions
when operating the tool.
SOLID E‑Clutch
®
System
has been
activated
(ENGAGED)
With the tool properly supported,
release trigger. The tool will
function normally when the trigger
is depressed again and the indicator
light will go out

WARNING: Drill may stall if overloaded causing a
sudden twist. Always expect the stall. Grip the drill
firmly to control the twisting action and avoidinjury.
Proper hand position requires one hand on the main
handle
9
, with the other hand on the side handle
6
.
Proper Hand Position (Fig.A, K)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
into the handle until the battery pack is firmly seated in the
tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
8
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Wireless Tool Control (Fig.A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
thetool.
Your tool is equipped with a Wireless Tool Control transmitter
which allows your tool to be wirelessly paired with another
Wireless Tool Control device, such as a DeWALT dustextractor.
To pair your tool using Wireless Tool Control, depress the
trigger switch
1
and the Wireless Tool Control pairing button
on the seperate device. An LED on the seperate device will let
you know when your tool has been successfullypaired.
DWH200D Dust Extraction System
(Fig.H)
Your heavy‑duty cordless rotary hammer comes with an
adapter for the DWH200D dust extractionsystem.
The standard SDS Plus tool holder adapter (short) comes
attached in the DWH200D. Your tool requires the included
longer holder adapter.
1. Remove the cross head screw
25
from the short
adapter
21
using a cross head screwdriver (Fig.H).
2. Then use the screw
25
to assemble the long tool holder
adapter
22
to the dust brush body
20
. Tightensecurely.
3. Slide the newly assembled dust brush
20
and tool
holder adapter
22
into the slot
23
on the top of the
side handle assembly
6
until you hear an audible click.
4. Connect dust extractor
24
to the dust brush
assembly
20
(Fig.H).
To Install the Belt Hook
1. Insert the hook into one of the slots, on left or right side,
below the main handle.
2. Install the screw on the underside of the mainhandle. Be
sure to securely tighten thescrew.
To Remove or Move the Belt Hook
1. Remove the screw located on the underside of the
mainhandle.
2. Pull the belt hook away from the main handle.
3. Insert the hook into one of the slots, on left or right
side, below the main handle, or install the screw on the
underside of the mainhandle. Be sure to securely tighten
thescrew.
Installing and Removing the Battery Pack
(Fig.F)
NOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
7
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it

DeWalt DCH416 Specifications

General

Brand	DeWalt
Model	DCH416
Category	Rotary Hammer
Language	English