DeWalt DWV902M User Manual

10
ENGLISH
Optional Accessories

WARNING: Since accessories, other than those offered by
DeWALT
, have not been tested with this product, use of
such accessories with this appliance could be hazardous.
To reduce the risk of injury, only
DeWALT
recommended
accessories should be used with this product.
ACCESSORIES
DWV9340-XJ Filter
DWV9315-XJ Crush-proof hose
DWV9316-XJ Anti-static hose
DWV9401-XJ Paper bag
DWV9400-XJ Plastic liner
DWV9402-XJ Fleece bag
DWV9500-XJ Vac Rack
DeWALT
AirLock System
DWV9000 Twist-Lock connection
DWV9110 29–35mm tapered
rubber adapter
DWV9120 35–38mm stepped
rubber adapter
DWV9130 35mm OD adapter
DWV9150 35mm OD angle
adapter
Vac Rack DWV9500 Installation (Fig. K, L)
NOTE: The DWV902MT comes with DWV9500 vac rack
attachment already installed,
1. Remove the 4 carry handle screws using a T-25 star bit and
remove the carry handle.
2. Install the vac rack reusing the carry handle screws. Put
them back in their original holes and tighten.
3. Use the 2 screws
28
provided by placing them in the rear
holes of the vac rack. Push down and turn each screw to
break through the material and into the hidden screw boss
below. Tighten.

CAUTION: Do not exceed 9 kg (20 lb) in each 14liter
storage unit, maximum 2 storage units per dust
extractor. Do not exceed 18 kg (40 lb) in a 28 liter storage
unit, 1 storage unit per dust extractor. Exceeding the
recommended height and/or weight could result in
an unstable dust extractor would could cause injury or
damage.
NOTICE: Do not remove dust extractor head from tank
with T-stack storage units attached. Doing so could result
in damage to the dust extractor filter.
Securing the Power Cord to the
Hose (Fig. A)
The power cord
2
can be secured to the suction hose
7
using
the D279058CL hose clip(available from your local D
e
WALT
supplier).
Consult your dealer for further information on the appropriate
accessories.
Troubleshooting
Problem Solution
Motor does
not run
Check power cord, plugs and outlet.
Ensure the on/off /tool control switch is in the
ON position ( ).
Suction
capacity
decreases
Remove blockages in the suction nozzle,
suction tube, suction hose or filters.
Replace the paper or fleece bag.
Check for proper installation of the filters.
Clean or replace the filters.
Empty canister, refer to Empty Canister under
Operation.
Vacuum
stops
running
Thermal overload has been tripped:
1. Turn the vacuum off and disconnect
vacuum cleaner from power source.
2. Empty the canister, if needed.
3. Allow the unit to cool.
4. Plug the power cord into an appropriate
outlet and turn on/off/tool control switch
to the ON position ( ) to test. If vacuum will
not restart contact your seller or check the
location of your nearest authorised
DeWALT
repair agent in the
DeWALT
catalogue or
contact your
DeWALT
office at the address
indicated in this manual.
Dust comes
out while
vacuuming
Check for proper installation of the filters.
Ensure filters are not damaged; replace if
necessary.
Ensure filter seals are in place and are secure.
Automatic
filter
cleaning is
not working
Listen for the solenoid clicking to ensure the
filter cleaning mechanism is working.
Power tool
does not
turn on.
Ensure the on/off/tool control switch is in the
ACTIVATION position .
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.

DeWalt DWV902M Specifications

General

Input power	1400 W
Airflow	68 l/s
Capacity	35 L
Noise level	73 dB
Number of wheels	4 wheel(s)
Product color	Black, Yellow

Weight and Dimensions

Weight	15000 g