4445103214 13
Storing the tent
I
1. Clean the tent.
2. Air fully and ensure the tent is totally dry before packing away.
3. Store in a well ventilated dry place.
Troubleshooting
I
Condensation
All tents suffer from internal condensation if one or more of the following
conditions apply:
• High air humidity
• High ground moisture
• A drop in temperature
Severe condensation can run down the inside of the roof and drip off ties,
tapes and other internal fittings and can be mistaken for leaking.
➤ Increase ventilation by opening doors and/or windows.
➤ Install a waterproof groundsheet.
Repairing a puncture in the air pole
If the air pole loses air, proceed as follows:
1. Unzip the outer sleeve holding the air pole.
2. If installed, close isolation valves.
3. Remove the air pole.
4. Deflate the air pole.
5. Unzip the protective sleeve to expose the inflatable tube.
6. Blow some air into the inflatable tube.
7. Submerge the tube in water.
8. Locate the puncture.
9. Use repair tape and repair solution to seal the hole.
10. Zip the inflatable tube back into the protective sleeve.
11. Zip the air pole back into the outer sleeve.
Disposal
Warranty
The statutory warranty period applies. If the product is defective, please
contact your retailer or the manufacturer's branch in your country (see
dometic.com/dealer).
For repair and warranty processing, please include the following docu-
ments when you send in the product:
• A copy of the receipt with purchasing date
• A reason for the claim or description of the fault
Note that self-repair or non-professional repair can have safety conse-
quences and might void the warranty.
The warranty covers manufacturing defects, materials and parts. The
warranty does not cover fading of the cover and wear and tear due to
UV radiation, misuse, accidental damage, storm damage, or permanent,
semi-permanent or commercial use. It does not cover any resulting
damage. Please contact your dealer for claims. This does not affect your
statutory rights.
NOTE
• Fully set up the tent for cleaning.
• Choose a sunny day for cleaning to ensure the material
will dry thoroughly.
NOTE
• During first exposure to water there may be some
moisture at the seams. Through this moisture the threads
will swell and fill the holes that are created in the sewing
process.
• A fully equipped spare parts kit should include:
– Waterproofer
– Repair tape and repair solution
– Silicone spray for the zippers
– Spare pegs
Problem Solution
Tent only inflates with diffi-
culties
➤ Check that the valve is fully screwed into the air
pole.
➤ Check if the inflation tube is twisted at the
valve.This may be indicated by noise. Untwist
the inflation tube.
➤ Check that the hand pump is working.
Part of the tent does not
inflate
➤ Check that all isolation valves that connect the
air poles are open.
Part of the tent does not
deflate
➤ Check that all isolation valves that connect the
air poles are open.
Air poles are kinked ➤ Add more air (9 psi/0.62 bar).
Air leak ➤ Check that the valve is fully screwed into the air
pole and the ring seal is in place.
➤ Check that the cap of the valve is done up
tightly.
➤ Check for punctures, see chapter “Condensa-
tion” on page 13.
Water leak ➤ Check for leaky seams, damaged tapings and
moist areas.
➤ If you cannot find any leaks, see chapter “Con-
densation” on page 13.
➤ If you find any leaks, apply seam sealant.
Rip in the fabric ➤ Use repair tape to seal the fabric.
➤ Have repairs carried out by an authorized
specialist.
➤ Place the packaging material in the appropriate recycling
waste bins wherever possible.
➤ Consult a local recycling center or specialist dealer for
details about how to dispose of the product in accordance
with the applicable disposal regulations.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
