EasyManuals Logo
Home>Fagor>Dishwasher>LVF11A

Fagor LVF11A User Manual

Fagor LVF11A
196 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of
the water used. This is intended to optimise and customise the level o f salt consumption.
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to eliminate
lime and minerals from the water.
4.Prior using for the first time4.Prior using for the first time
Contact your local water board for information on the hardness of your water supply.
55
A. Water SoftenerA. Water Softener
NOTE:NOTE:
If your model does not have any water softener, you may skip this section.
¡ã
Clark: British degree
¡ã
fH: French degree
¡ã
dH: German degree
Note:1Note:1
dH=1.25 Clarke=1.78 fH=0.178mmol/l
¡ã
¡ã
¡ã
1
Note:2Note:2
The manufactory setting: H3 (EN 50242)
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
dH
mmol/l
0~90~5 0~0.94
H1
0
10-20
6-11
1.0-2.0
H2
9
21-30
12-17 2.1-3.0
H3
12
H4
20
fH
0~6
7-14
15-21
Clarke
WATER HARDNESS
Selector Position
Salt c onsumption
(gram/cycle)
18-22 31-40 22-28 3.1-4.0
41-60
23-34 4.1-6.0
H5
30
H6
60
29-42
35-55 61-98 43-69 6.1-9.8
1. Switch on the appliance;
2. Press the Start/Pause button for more than 5 seconds to start the water
softener set model within 60seconds after the appliance was
switched on;
3. Press the Start/Pause button to select the proper set according to
your local environment, the sets will change in the following
sequence: H1->H2->H3->H4->H5->H6;
4. Press the On/Off button to end the set up model.
Please follow the steps below for adjustment in salt consumption.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fagor LVF11A and is the answer not in the manual?

Fagor LVF11A Specifications

General IconGeneral
Child lockYes
Door colorWhite
Control typeButtons
Display typeLED
Product sizeFull size (60 cm)
Appliance placementFreestanding
Noise level51 dB
Delay start (max)9 h
Dishwashing programsAuto, Glass/delicate
Number of place settings12 place settings
Number of washing programs6
Water consumption per cycle11.5 L
Energy consumption per cycle- kWh
Annual water consumption3220 L
Annual energy consumption290 kWh
Weight and Dimensions IconWeight and Dimensions
Depth598 mm
Width600 mm
Height815 mm
Height under worktop845 mm

Related product manuals