EasyManuals Logo
Home>gefran>Controller>1600P

gefran 1600P User Manual

gefran 1600P
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
96
115
108
96
113
10
92
92
115
48
70
115
44,5
92
113
10
108
96
1600P / 1800P
CONTROLLER / PROGRAMMER
SOFTWARE VERSION 3.2x
code 80090G / Edit 14 - 04-2013
INSTALLATION AND
OPERATION MANUAL
For correct and safe
installation, follow the
instructions and observe
the warnings contained in
this manual.
1 • INSTALLATION
Dimensions and cut-out; panel mounting
Panel mounting:
To fix the unit, insert the brackets provided into the seats on either side of the case. To mount
two or more units side by side, respect the cut-out dimensions shown in the drawing. To obtain
IP65 faceplate protection level, remove the device from the box, apply the gasket (supplied) with
adhesive to the front edge of the box, and then reinsert the device.
CE MARKING: The instrument conforms to the European Directives 2004/108/CE and
2006/95/CE with reference to the generic standards: EN 61000-6-2 (immunity in industrial
environment) EN 61000-6-3 (emission in residential environment) EN 61010-1 (safety).
Limitations: model 1800P conforms to Standard EN61000-6-4 for emissions radiated in
industrial environment.
MAINTENANCE: Repairs must be done only by trained and specialized personnel.
Cut power to the device before accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene, etc.).
Use of these solvents can reduce the mechanical reliability of the device. Use a cloth
dampened in ethyl alcohol or water to clean the external plastic case.
SERVICE: GEFRAN has a service department. The warranty excludes defects caused by
any use not conforming to these instructions.
2 • TECHNICAL SPECIFICATIONS
FUNCTION CABLE TYPE LENGTH
Power supply cable 1 mm
2
1 m
Relay output cable 1 mm
2
3,5 m
Digital communication wires 0,35 mm
2
3,5 m
C.T. connection cable 1,5 mm
2
3,5 m
TC input 0,8 mm
2
compensated 5 m
Pt100 input 1 mm
2
3 m
EMC conformity has been tested with the following connections
!
5 mechanical keys (, Man/Auto, INC, DEC, F)
RTD type (scale configurable within indicated
range, with or without decimal point)
PTC type (on request)
DIN 43760 (Pt100, JPT100)
990Ω, 25°C
Max line resistance for RTD 20Ω
Safety
detection of short-circuit or opening of probes,
LBA alarm, HB alarm
°C / °F selection configurable from faceplate
Linear scale ranges -1999 to 9999 with configurable decimal point position
Thermocouples
IEC 584-1
(J, K, R, S, T, B, E, N, Ni-Ni18Mo, L NiCr-CuNi)
Cold junction error 0,1° / °C
Controls PID, Self-tuning, on-off
pb / dt / di 0.0 ... 999.9% / 0.00 ... 99.99min / 0.00 ... 99.99min
Action Heat / Cool
Control outputs on / off, pwm
Cycle time 0.1 ... 200 sec
Main output type Relay, Logic, Continuous (optional)
Softstart 0.0 ... 500.0 min
Maximum power limit heat / cool 0.0 ... 100.0 %
Fault power setting -100.0 ... 100.0 %
Automatic blanking Optional exclusion, displays PV value
Configurable alarms
3 configurable alarms type: max, min, symmetrical,
absolute or relative, LBA, HB
Alarm masking
- exclusion during warm up
- latching reset from faceplate or external contact
Type of relay contact NO (NC), 5A, 250V, cosϕ = 1
Faceplate protection IP65
Working / Storage temperature range 0...50°C / -20...70°C
Relative humidity 20 ... 85% non-condensing
Installation Panel, plug-in from front
Weight 400g (1600P); 600g (1800P) complete version
Main input
TC, RTD (Pt100 - JPT100), PTC,
50mV Ri ≥ 1MΩ; 10V Ri ≥ 10KΩ; 20mA, Ri = 50Ω
CT scale range configurable 0, ... , 100.0A
Transmitter power supply (optional)
filtered 10 / 24Vdc, max 30mA
short-circuit protection, isolation 1500V
Analogue retransmission signal (opt) 10V / 20mA, isolation 1500V
Logic inputs (optional) 24V NPN, 4.5mA; 24V PNP, 3.6mA isolation 1500V
Serial interface (optional) CL; RS422/485; RS232; isolation 1500V
Baud rate 1200 ... 19200
Protocol GEFRAN / MODBUS
Logic output for static relays 11Vdc, Rout = 220Ω (6V/20mA)
Remote setpoint or
ammeter input (options)
0 ... 10V, 2 ... 10V, Ri ≥ 1MΩ
0 ... 20mA, 4 ... 20mA, Ri = 5Ω
Potentiometer > 500Ω,
TA 50mAac, 50/60Hz, Ri = 1,5Ω,
isolation 1500V
Power supply (switching type)
(std) 100 ... 240Vac/dc ±10%; 50/60Hz, 12VA max
(opz.) 20...27Vac/dc ±10%; 50/60Hz, 12VA max
Display
2 x 4 digits, green, height 10 and 7mm (1600P), 20 and 30 mm (1800P)
Keys
Accuracy 0.2% full scale at 25°C room temperature
Environmental conditions of use for internal use only, altitude up to 2000m
180090G_MHW_1600-1800P_04-2013_ENG

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the gefran 1600P and is the answer not in the manual?

gefran 1600P Specifications

General IconGeneral
Brandgefran
Model1600P
CategoryController
LanguageEnglish

Related product manuals