Graco XM User Manual

Technical Data
31
Technical Data
* Minimum flow rate is dependent on material being sprayed and mixing capability. Test your material specific to
flow rate.
Mixed ratio range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1-10:1 (in 0.1 increments)
Ratio tolerance range . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 5%
Flow rates
Minimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 qt./min. (0.95 liter/min.)*
3 gal./min/ (11.4 liter/min.)
Fluid viscosity range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-20,000 cps (heavier viscosities can be mixed using
heat, circulation, and/or pressure feeding)
Fluid filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mesh, (238 micron) standard on pump outlets (filter
assembly not included on some models)
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npt(f)
Fluid inlets without feed kits . . . . . . . . . . . . . . . . . . . . . . . 1 1/4 npt(m)
Maximum fluid working pressure of mixed material
50:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5200 psi (35.8 MPa, 358 bar)
6300 psi (43.5 MPa, 435 bar)
Maximum fluid temperature . . . . . . . . . . . . . . . . . . . . . . . 160° F (71° C)
Air supply pressure range. . . . . . . . . . . . . . . . . . . . . . . . . 50-150 psi (0.35-1.0 MPa, 3.5-10.3 bar)
Maximum pump air set pressure
50:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100 psi (0.7 MPa, 7.0 bar)
90 psi (0.62 MPa, 6.2 bar)
Maximum pump inlet fluid feed pressure . . . . . . . . . . . . . 250 psi (1.7 MPa, 17 bar)
Maximum air consumption at 100 psi (0.7 MPa, 7.0 bar)
in scfm (m
3
/min.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 scfm per gpm (1.96 m
3
/min. per lpm)
Ambient temperature range
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32-135° F (0-57° C)
30-160° F (-1-71° C)
Environmental conditions rating . . . . . . . . . . . . . . . . . . . . Indoor/outdoor use
Altitude up to 4000 m
Maximum relative humidity to 99% up to 130° F (54° C)
Pollution degree (11)
Installation category (2)
Sound pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 dBA at 100 psi (0.7 MPa, 7 bar)
Sound power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dBA at 100 psi (0.7 MPa, 7 bar)
Wetted parts
Suction tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flush pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hoses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pumps (A and B) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metering valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
aluminum
carbide, PTFE, stainless steel, UHMWPE
nylon
carbon steel, alloy steel, 303, 440, 17-ph grades stainless
steel, zinc and nickel plating, ductile iron, tungsten car-
bide, PTFE, leather
carbon steel, nickel plating, carbide, polyethylene, leather
carbon steel, nickel plating, carbide, 302 stainless steel,
PTFE, UHMWPE
stainless steel housing with acetal elements
Refer to spray gun manual

Graco XM Specifications

General

Brand	Graco
Model	XM
Category	Paint Sprayer
Language	English