Installation Manual
Safety Precautions f
or Electrical Wiring
Earthing requirements
Installation Site of Outdoor Unit
1
.
WhereQRLVHDQGRXWIORZDLUHPLWWHGE\XQLWZLOOQRWannoy neighbors.
WKHUHWKHUHisVXIILFLHQWYHQWLODWLRQ
WKHUHWKHUHis QRREVWUXFWLRQ blockingWKHair LQOHWorRXWOHW.
Where it isDEOHWRZLWKVWDQGWKHIXOOZHLJKWDQGYLEUDWLRQ.
Where it is dry and the unit is not exposed to direct sunshine or strong wind
0DNHVXUHWKDWWKHRXWGRRUXQLWis installed in accordance with the installation instructions,
and is convenient for maintenance and repair.
KHLJKWGLIIHUHQFHbetween indoor and outdoor units is within 16ft, and the length of
the connecting tubing does not exceed 32ft.
WKHUHLWLVRXWRIUHDFKofFKLOGUHQ
5. The minimum distance between the unit and combustive surface is 5ft.
A dedicated power supply circuit should be used in accordance with local electrical
safety regulations.
2. 'RQWGUDJWKHSRZHUcord.
3.
The appliance shall be installed in accordance with national wiring regulations.
An all-pole disconnection switch having a contact separation of at least 1/8inch in all poles
should be connected in fixed wiring.
The unit VKRXOGEHUHOLDEO\ HDUWKHG DQG FRQQHFWHGWRan exclusiveHDUWKGHYLFH by the
SURIHVVLRQDOs
4.
7KHDLUVZLWFK PXVWKDYHWKHIXQFWLRQVRI PDJQHWLFWULSSLQJDQGKHDWWULSSLQJ to prevent
VKRUW FLUFXLW DQG RYHUORDGLQJ
ķ
ĸ
Ĺ
ĺ
$LUFRQGLWLRQHULVW\SHI HOHFWULFDSSOLDQFH. POHDVH ensure the the unit is reliably earthed.
7KH\HOORZJUHHQ ZLUH LQ DLU FRQGLWLRQHULV theHDUWKLQJZLUHwhichFDQ QRWEHXVHG
IRURWKHUSurSRVHs
Improper earthing may cause electric shock.
7KHHDUWKUHVLVWDQFHVKRXOGDFFRUGWRWKHnDWLRQDOcULWHULRQ
7KHXVHU's SRZHUPXVWhave UHOLDEOHHDUWKLQJWHUPLQDO3OHDVHGRQWFRQQHFWWKH earthing
wire with WKHIROORZLQJ
:
WDWHUSLSH
*DV SLSH
&RQWDPLQDWLRQSLSH
2WKHUSODFHWKDWSURIHVVLRQDOSHUVRQQHOFRQVLGHU is XQUHOLDEOH
5
The model and rated values of fuses should accord with the silk print on fuse cover or related
PCB.
6.
7.
2.
3.
4.
5.
6.
7.
8.
9.
Install the outdoor unit:
Where
the
Where the unit does not have negative impact on pedestrian or city amenity.
CAUTION
!
EQUIPMENT DAMAGE HAZARD
Failure to follow this caution may result in equipment
damage or improper operation.
S Be sure to comply with local codes while running wire
from indoor unit to outdoor unit.
S Every wire must be connected firmly. Loose wiring may
cause terminal to overheat or result in unit malfunction.
A fire hazard may also exist. Therefore, be sure all wiring
is tightly connected.
S No wire should be allowed to touch refrigerant tubing,
compressor or any moving parts.
S Disconnecting means must be provided and shall be
located within sight and readily accessible from the air
conditioner.
S Connecting cable with conduit shall be routed through
hole in the conduit panel.
NOTE: Polarity of power wir es must match original
connection on outdoor unit.
22