Gree GWH18UC-K3DNA1A/I User Manual


)XQFWLRQDQG&RQWURO
Press this button, the Quiet status is under the Auto Quiet mode (display " "signal )and Quiet mode (display " " singal) and
Quiet OFF (there is no signal of " " displayed),after powered on, the Quiet OFF is defaulted. Note: the Quiet function cannot
be set up in Fan and Dry mode;Under the Quiet mode (Display " " Under the Quiet mode (Display " " signal), the fan
speed is not available.
Press CLOCK button, blinking . Within 5 seconds,pressing +or - button adjusts the present time.Holding down either button
above 2 seconds increases or decreases the time by 1 minute every 0.5 second and then by 10 minutes every 0.5 second. During
blinking after setting, press CLOCK button again to confirm the setting,and then will be constantly displayed.
Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply press this button again.
After press of this button, disappears and "ON "blink s .00:00 is displayed for ON time setting. Within 5 seconds, press + or -
button to adjust the time value. Every press of either button changes the time setting by 1 minute. Holding down either button
rapidly changes the time setting by 1 minute and then 10 minutes. Within 5 Seconds after setting, press TIMER ON button to
confirm. Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply press the button again.TIMER
OFF setting is the same as TIMER ON.
Press this button to activate / deactivate the Turbo function which enables the unit to reach the preset temperature in the shortest
time. In COOL mode, the unit will blow strong cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating
air at super high fan speed.
Press LIGHT button to turn on the display's light and press this button again to turn off the display 's light. If the light is turned on ,
is displayed. If the light is turned off, disappears.
Pressing X-FAN button in COOL or DRY mode,the icon is displayed and the indoor fan will continue operation for 10 minutes
in order to dry the indoor unit even though you have turned off the unit.
After energization, X-FAN OFF is defaulted. X-FAN is not available in AUTO,FAN or HEAT mode.
Combination of "+" and "-" buttons: About lock
Press "+ " and "-" buttons simultaneously to lock or unlock the keypad. If the remote controller is locked, is displayed. In this
case, pressing any button, blinks three times.
Combination of "MODE " and "-" buttons : About switch between Fahrenheit and centigrade At unit OFF, press "MODE" and " - "
buttons simultaneously to switch between ℃ and ℉ .
Combination of " TEMP " and "CLOCK" buttons : About Energy-saving Function
Press “TEMP” and “CLOCK” simultaneously in COOL mode to start energy-saving function. Nixie tube on the remote controller
displays “SE”. Repeat the operation to quit the function.
Combination of " TEMP " and "CLOCK" buttons : About 8℃ Heating Function
Press “TEMP” and “CLOCK” simultaneously in HEAT mode to start 8℃ Heating Function Nixie tube on the remote controller
displays “ ” and a selected temperature of “ 8℃”. (46 ℉if Fahrenheit is adopted). Repeat the operation to quit the function.
About Back-lighting Function
The unit lights for 4s when energizing for the first time, and 3s for later press.
11
QUIET
12
CLOCK
T-ON T-OFF
13
14
TURBO
15
LIGHT
17
16
X-FAN
18
19
20
21
AUTO
Replacement of Batteries
1.Remove the battery cover plate from the rear of the remote controller.
(As shown in the figure)
2.Take out the old batteries.
3.Insert two new AAA1.5V dry batteries, and pay attention to the polarity.
4. Reinstall the battery cover plate.
★Notes:
●When replacing the batteries, do not use old or different types of batteries,
●If the remote controller will not be used for a long time, please
otherwise, it may cause malfunction.
remove batteries to prevent batteries from leaking.
●The operation should be performed in its receiving range.
●It should be kept 1m away from the TV set or stereo sound sets.
●If the remote controller does not operate normally, please take the
batteries out and reinsert them after 30 seconds.If it still can't operate properly,
replace the batteries.
Sketch map for
replacing batteries

Gree GWH18UC-K3DNA1A/I Specifications

General

Brand	Gree
Model	GWH18UC-K3DNA1A/I
Category	Air Conditioner
Language	English