EasyManuals Logo
Home>HIKVISION>Network Hardware>DS-7608NI-Q1/8P

HIKVISION DS-7608NI-Q1/8P User Manual

HIKVISION DS-7608NI-Q1/8P
226 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #169 background imageLoading...
Page #169 background image
Network Video Recorder User Manual
168
Senders Address: The Email address of sender.
Select Receivers: Select the receiver. Up to 3 receivers can be configured.
Receiver: The name of user to be notified.
Receivers Address: The Email address of user to be notified.
Enable Attached Picture: Check the checkbox of Enable Attached Picture if you want to send
email with attached alarm images. The interval is the time of two adjacent alarm images. You
can also set SMTP port and enable SSL here.
Interval: The interval refers to the time between two actions of sending attached pictures.
Step 6 Click Apply button to save the Email settings.
Step 7 You can click Test button to test whether your Email settings work.
11.2.9 Configuring NAT
Purpose:
Two ways are provided for port mapping to realize the remote access via the cross-segment
network, UPnP and manual mapping.
UPnP
TM
Universal Plug and Play (UPnP™) can permit the device seamlessly discover the presence of other
network devices on the network and establish functional network services for data sharing,
communications, etc. You can use the UPnP™ function to enable the fast connection of the device
to the WAN via a router without port mapping.
Before you start:
If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of
the router to which your device is connected. When the network working mode of the device is set
as multi-address, the Default Route of the device should be in the same network segment as that
of the LAN IP address of the router.
Step 1 Enter the Network Settings interface.
Menu > Configuration > Network
Step 2 Select the NAT tab to enter the port mapping interface.
Figure 11-22 UPnPSettings Interface

Table of Contents

Other manuals for HIKVISION DS-7608NI-Q1/8P

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HIKVISION DS-7608NI-Q1/8P and is the answer not in the manual?

HIKVISION DS-7608NI-Q1/8P Specifications

General IconGeneral
Two-way talkYes
Input bandwidth80 Mbit/s
Number of users64 user(s)
Maximum resolution4096 x 2160 pixels
Video input channels8 channels
Supported resolutions4096 x 2160, 3840 x 2160, 2560 x 1440, 1920 x 1080, 1600 x 1200, 1280 x 1024, 1280 x 720
Audio formats supportedG.711 A-law, G.711 μ-law, G.726
Video formats supportedH.264, H.264+, H.265, H.265+, MPEG4
CertificationFCC Part 15 Subpart B, ANSI C63.4-2014 CE EN 55032: 2015, EN 61000-3-2, EN 61000-3-3, EN 50130-4, EN 55035: 2017
Product colorBlack
Rack capacity1U
Audio RCA outputs1
Networking standardsIEEE 802.3af, IEEE 802.3at
USB 2.0 ports quantity2
Ethernet LAN data rates10, 100 Mbit/s
Supported network protocolsTCP/IP, DHCP, IPv4, IPv6, DNS, DDNS, NTP, RTSP, SADP, SMTP, SNMP, NFS, iSCSI, ISUP, UPnP, HTTP, HTTPS
Power over Ethernet (PoE) ports quantity8
Wi-FiNo
HDD capacity- GB
HDD interfaceSATA
Maximum storage capacity8 TB
Number of HDDs installed0
Operating temperature (T-T)-10 - 55 °C
Operating relative humidity (H-H)10 - 90 %
Power consumption (typical)10 W
Total Power over Ethernet (PoE) budget75 W
Weight and Dimensions IconWeight and Dimensions
Depth240 mm
Width320 mm
Height48 mm
Weight1000 g

Related product manuals