Material
to be cut
Below
4-3/4 (120)
General lumber
Nonferrous
metal
Foamed polyethylene,
foamed styrol
Plywood
Fiberboard
Hardboard
Cardboard,
corrugated paper
Vinyl chloride,
acryl resin, etc.
Phenol resin,
melamin resin, etc.
Aluminum sash
Aluminum
copper, brass
Stainless steel
plate
Mild steel plate
Lumber
Iron
plate
Plastics
Pulp
Blade
Material
quality
No. 1 (Long)
Thickness of material: inch (mm)
123XNo. 15 No. 16, 46No. 12, 42 No. 97No. 22No. 21, 41No. 11
8. BLADES
Proper blade selection is very important to obtain the maximum performance of this model. The table below,
based on type and thickness of the material to be cut, can be used as a handy reference is selecting the optimum
blade.
3/8-2 - 11/32
(10 - 60)
3/8 - 2-11/32
(10 - 60)
3/8 - 2-11/32
(10 - 60)
3/8 - 2-11/32
(10 - 60)
3/8 - 2-11/32
(10 - 60)
Below
3/4 (20)
3/8 - 2-11/32
(10 - 60)
Below
1/4 (6)
Below
3/16 (5)
Below
3/8 (10)
Below
3/8 (10)
1/8 - 1-3/16
(3 - 30)
3/16 - 1-3/16
(5 - 30)
1/8 - 1-3/16
(3 - 30)
3/16 - 3/4
(5 - 20)
3/16 - 1-3/16
(5 - 30)
1/8 - 1-1/2
(3 - 40)
3/8 - 2
(10 - 50)
3/16 - 1-3/16
(5 -30)
1/8 - 1-1/2
(3 - 40)
3/16 - 1-3/16
(5 -30)
1/8 - 1-3/16
(3 - 30)
Below
1/4 (6)
Below
1/4 (6)
Below
1/4 (6)
1/8 - 3/8
(3 - 10)
1/8 - 15/32
(3 - 12)
3/16 - 3/4
(5 - 20)
1/8 - 1-3/16
(3 - 30)
1/8 - 1-3/16
(3 - 30)
Below
3/16 (5)
3/16 - 19/32
(5 - 15)
3/16 - 19/32
(5 - 15)
5/54 - 3/16
(2 - 5)
1/16 - 5/32
(1.5 - 2.5)
3/16 - 19/32
(5 - 15)
3/16 - 1-3/16
(5 - 30)
1/8 - 3/8
(3 - 10)
1/8 - 15/32
(3 - 12)
3/16 - 3/4
(5 - 20)
1/8 - 1-3/4
(3-20)
3/16 - 1-9/16
(5 - 40)
3/16 - 1-3/16
(5 -30)
Below
1/8 (3)
Below
1/8 (3)
Height
up to
1-3/16 (30)
1/8 - 1-3/16
(3 - 30)
3/16 - 1-3/16
(5 -30)
1/8 - 3/4
(3 - 20)
NOTE:
The minimum cutting radius of No. 1 (Long), No. 21, No. 22 and No. 41 blades is 3-15/16" (100 mm ).
No. 1 (Long), No. 11, No. 12, No. 15, No. 16, No. 21, No. 22 and No. 97 blades are sold separately.
3/8 - 2
(10 - 50)
3/16 - 1-3/16
(5 - 30)
Height
up to
1-3/16 (30)
Height
up to
1-3/16 (30)
3/8 - 2
(10 - 50)
To Next Page
Loading...
Need help?
General
