9
English
NOTE
2.5 mm × 64 mm (.099" × 2-1/2") nails cannot be
driven in some cases, depending on the material.
Test drive some of the nails first to check before
using.
PREPARATION PRIOR TO OPERATION
1. Prepare the hose
Be sure to use the hose provided with minimum
6 mm (1/4”) inside diameter.
NOTE
The air supply hoses must have a minimum working
pressure rating of 12.8 bar (180 psi) or 150 percent of
the maximum pressure produced in the air supply
system, whichever is higher.
2. Check on safety
CAUTION
䡬 Unauthorized persons (including children) must be
kept away from the equipment.
䡬 Wear eye protector.
䡬 Check the retaining screws which fix the exhaust
cover, etc. for tightness.
Check the nailer for air leaks and defective or rusty
parts.
䡬 Check whether or not the push lever works correctly.
Also check whether or not any dirt has adhered to the
moving parts of the push lever.
䡬 Recheck on operational safety.
BEFORE USE
1. Check the air pressure
CAUTION
The air pressure must be constantly maintained at
4.9 – 8.3 bar (70 – 120 psi.).
Adjust the air pressure between 4.9 to 8.3 bar (70 ~
120 psi.) according to the diameters and length of
nails and hardness of the wood being nailed. Pay
special attention to the output pressure, capacity,
and piping on the air compressor, so that air pressure
does not exceed the specified limit. Note that
excessive pressure may affect overall performance,
service life, and safety.
2. Lubrication
(1) Prior to operating this nailer, be sure to provide an air
set between the air compressor and this device.
Lubrication through the air set offers smooth
operation, extended service life, and anticorrosion.
Adjust the oiler so that a single drop of oil is supplied
at intervals of 5 to 10 nailing cycles.
Dimensions of nails
STANDARD ACCESSORIES
(1) Eye protector .............................................................. 1
OPTIONAL ACCESSORY
䡬 Single Shot Parts (Code No. 887-916)
(Sequential Fire Parts Set, Single Shot Parts)
With the sequential fire parts,the nail is driven only
by squeezing the trigger after pushing down the
push lever.
By installing these parts, driving nails into improper
positions and unexpected firing of nails caused by
accidental operation of the push lever can be
prevented.
䡬 Case (Code No. 880-517)
䡬 Nose Cap (Code No. 878-344)
䡬 Hanger Parts (Code No. 888-097)
APPLICATIONS
䡬 Siding, fencing, decking
䡬 Wall and roof sheathing
䡬 Mobile home and modular housing construction
䡬 Crate and pallet construction
NAIL SELECTION
Wire collated nails and plastic collated nails can be driven
with this tool.
Choose a suitable nail from Fig. Nails which are not
shown in Fig. can not be driven with this tool. Nails are
linked and rolled.
SPECIFICATIONS
Type of power Piston reciprocating
Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)
Applicable nails ref. Fig.
Amount of loadable nails 200 – 300 nails (1 coil)
Size 290 mm (L) × 300 mm (H) × 130 mm (W) (11-27/64” × 11-13/16” × 5-1/8”)
Weight 2.2 kg (4.9 lbs)
Nail-feeding method Piston reciprocation
Hose (inside diam.) 7 mm (9/32”)
Wire-collatd coil nails Sheet-collated coil nails
MIN. MAX. MIN. MAX.
5.3 mm 6.4 mm 5.3 mm 6.4 mm
(.209”) (.252”) (.209”) (.252”)
57 mm (2-1/4”)
2.3 mm
(.090”)
2.3 mm
(.090”)
65 mm (2-1/2”)
38 mm (1-1/2”)
38 mm (1-1/2”)
2.5 mm
(.099”)
2.5 mm
(.099”)
01Eng_NV65AH2_WE.p65 8/2/13, 11:16 AM9
To Next Page
Loading...
Need help?
General
