Status regarding
compliance with
IEC 61000-3-2 and
IEC 61000-3-12
Models
Split system
Monobloc
system
Outdoor unit
Indoor unit
YUTAKI M
(R410A) /
YUTAKI M
(R32)
YUTAKI S YUTAKI S COMBI YUTAKI S80
Equipment complying with
IEC 61000-3-2
(*): Professional use
RAS-2WHVNP
RAS-2.5WHVNP
RAS-3WHVNP
RAS-2WHVRP(*)
RAS-2.5WHVRP(*)
RAS-3WHVRP (*)
RAS-4WHNPE (*)
RAS-5WHNPE (*)
RAS-6WHNPE (*)
RWM-2.0NRE(-W)
RWM-2.5NRE(-W)
RWM-3.0NRE(-W)
RWM-4.0NE(-W) (3N~)
RWM-5.0NE(-W) (3N~)
RWM-6.0NE(-W) (3N~)
RWM-8.0NE(-W)
RWM-10.0NE(-W)
-
RWH-4.0NFE
RWH-5.0NFE
RWH-6.0NFE
RASM-2VRE(*)
RASM-3VRE(*)
RASM-4NE
RASM-5NE
RASM-6NE
Equipment complying with
IEC 61000-3-12
RAS-4WHVNPE
RAS-5WHVNPE
RAS-6WHVNPE
RWM-4.0NE(-W) (1~)
RWM-5.0NE(-W) (1~)
RWM-6.0NE(-W) (1~)
RWD-2.0NRWE-200S(-W)
RWD-2.0NRW(S)E-260S(-W)
RWD-2.5NRWE-200S(-W)
RWD-2.5NRW(S)E-260S(-W)
RWD-3.0NRWE-200S(-W)
RWD-3.0NRW(S)E-260S(-W)
RWD-4.0NWE-260S(-W)
RWD-4.0NW(S)E-260S(-W)
RWD-5.0NWE-260S(-W)
RWD-5.0NW(S)E-260S(-W)
RWD-6.0NWE-260S(-W)
RWD-6.0NW(S)E-260S(-W)
RWH-4.0VNFE
RWH-5.0VNFE
RWH-6.0VNFE
RWH-4.0VNFWE
RWH-5.0VNFWE
RWH-6.0VNFWE
RWH-4.0NFWE
RWH-5.0NFWE
RWH-6.0NFWE
RASM-4VNE
RASM-5VNE
RASM-6VNE
Installation restrictions may be
applied by supply authorities
in relation to harmonics
RAS-8WHNPE
RAS-10WHNPE
- - - -
• Check to ensure that existing installation (main power switches, circuit breakers, wires, connectors and wire terminals) already
complies with the national and local regulations.
• The use of the DHW tank heater is disabled as factory setting. If it is desired to enable the DHW tank heater operation during
normal indoor unit operation, adjust the DSW4 pin 3 of the PCB1 to the ON position and use the adequate protections. Refer to
the section “6.2 Electrical connection” for the detailed information.
ELECTRICAL AND CONTROL SETTINGS
PMML0510 rev.1 - 10/2019
48
To Next Page
Loading...
Need help?
General