BEFORE INSTALLING
If the modules will be installed in an existing operational system, inform the
operator and local authority that the system will be temporarily out of service.
Disconnect the power to the control panel before installing the modules. This
system contains static sensitive components. Always ground yourself with a
proper wrist strap before handling any circuits so that static charges are re-
moved from the body. The housing cabinet should be metallic and suitably
grounded.
NOTICE:This manual should be left with the owner/user of this equipment.
GENERAL DESCRIPTION
The XP6-C Six Circuit Supervised Control Module is intended for use in an
intelligent alarm system. Each module is intended for switching applications
involving AC, DC, or audio, which require wiring supervision. A common SLC
input is used for all modules. Each module has its own address. A pair of
rotary code switches is used to set the address of the first module from 01 to
N500-79-00 1 I56-1805-019
INSTALLATION AND MAINTENANCE INSTRUCTIONS
XP6-C
Six Circuit Supervised Control Module
SPECIFICATIONS
Normal Operating Voltage: 15-32 VDC
Stand-By Current: 2.65 mA @ 24V
Alarm Current: 35 mA (assumes all six relays have been switched once and all six LEDs solid on)
Temperature Range: 32°F to 120°F (0°C to 49°C); –10°C to 55°C (For EN54 applications only)
Humidity: 10 to 93% Non-condensing
Dimensions: 6.8
″
H x 5.8
″
W x 1.25
″
D
Accessories:
CHS-6 Chassis; BB-25 Cabinet; BB-XP Cabinet; CAB-3 Series Cabinet, CAB-4 Series
Cabinet
Wire Gauge: 12-18 AWG
Max. NAC Circuit Line Loss: 4 VDC
Power Rating Per Circuit (Speakers): 50 W @ 70.7 VAC; 50 W @ 25 VAC
Max. NAC Current Ratings: For class B wiring systems, 3A
For class A wiring systems, 2A
TABLE 1: SHORT CIRCUIT PROTECTION - UL 864 9TH EDITION REQUIREMENTS
NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION, AND OTHER INVOLVED PARTIES
This product incorporates field-programmable software. In order for the product to comply with requirements in the Standard for Control Units and
Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below.
PROGRAM FEATURE OR OPTION
PERMITTED IN
UL 864 (Y/N)
POSSIBLE SETTINGS SETTINGS PERMITTED IN UL 864
Disabling short circuit protection
when a single power supply is shared
by multiple NACs
No Enable or Disable short
circuit protection
Enable short circuit protection when a single power supply is
shared by multiple NACs. Short circuit protection can be disabled
only when a power supply is not shared by multiple NACs.
I56-1805-019
RELAY CONTACT RATINGS:
CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION
2 A 25 VAC PF = 0.35 Non-coded
3 A 30 VDC Resistive Non-coded
2 A 30 VDC Resistive Coded
0.46 A 30 VDC (L/R = 20ms) Non-coded
0.7 A 70.7 VAC PF = 0.35 Non-coded
0.9 A 125 VDC Resistive Non-coded
0.5 A 125 VAC PF = 0.75 Non-coded
0.3 A 125 VAC PF = 0.35 Non-coded
154. The remaining modules are automatically assigned to the next five higher
addresses. Provisions are included for disabling a maximum of three unused
modules to release the addresses to be used elsewhere. Each module also has
panel controlled green LED indicators. The panel can cause the LEDs to blink,
latch on, or latch off.
In order to synchronize strobes, horn/strobes, and speaker/strobes, a SYNC-1
accessory card (sold separately) must be used with the XP6-C. See the SYNC-1
installation manual for details on how to install.
Each module has terminals for connection to an external supply circuit for
powering devices on its NAC. Each supply must be power limited and its volt
-
age/current limits must be at or below those specified. There is a short circuit
protection monitor for each module. This is provided to protect the external
power supply against short circuit conditions on the NAC.
12 Clintonville Road
Northford, CT 06472-1653
Phone: 203.484.7161
To Next Page
Need help?
General
