Honeywell S8670J User Manual

บริษัท เอดีดี เฟอร์เนส จํากัด
ADD FURNACE CO.,LTD.
44 ซอยบรมราชชนนี 70 ถนนบรมราชชนนี แขวงศาลาธรรมสพน์ เขตทวีวัฒนา กรุงเทพฯ 10170
โทร: 02-888-3472 โทร: ออกแบบ:08-08-170-170 แฟกซ์: 02-888-3258
https://www.add-furnace.com E-mail: sales@add-furnace.com
S8600B,C,H,M; S8610B,C,H,M;
S8670D,E,J,K Intermittent Pilot
Gas Ignition Control
APPLICATION
The 8600 family of ignition controls provide ignition sequence, flame monitoring and safety shutoff for intermittent pilot
gas fired heating appliances. These controls provide flame sense and operating sequences suitable for the application.
Table 1 describes the main features of each available model.
Table 1. Intermittent Pilot Ignition Models.
Model
Igniter-
Sensor
Type
Valve
Current
Rating
@ 24 Vac
Prepurge
Timing
Trial for
Pilot
Ignition
Ignition
Sequence
Type
Ignition Sequence Description
a
S8600B
Separate
b
1.0 A Pilot
and
1.0 A Main
None
15 or 90
seconds,
as ordered
Lockout
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff), and
lockout. Cycle “Call for Heat” to restart ignition sequence.
S8600C
Separate
1.0 A Pilot
and
1.0 A Main
None
15 or 90
seconds,
as ordered
Continuous
Retry
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff). After
5 minute delay, a new trial for ignition is initiated. This sequence
continues until lightoff or “Call for Heat” is removed.
S8600H
Combination
c
1.0 A Pilot
and
1.0 A Main
None
15 or 90
seconds,
as ordered
Lockout
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff), and
lockout. Cycle “Call for Heat” to restart ignition sequence.
S8600M
Combination
1.0 A Pilot
and
1.0 A Main
None
15 or 90
seconds,
as ordered
Continuous
Retry
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff). After
5 minute delay, a new trial for ignition is initiated. This sequence
continues until lightoff or “Call for Heat” is removed.
S8610B
Separate
1.0 A Pilot
and
2.0 A Main
None
15 or 90
seconds,
as ordered
Lockout
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff), and
lockout. Cycle “Call for Heat” to restart ignition sequence.
S8610C
Separate
1.0 A Pilot
and
2.0 A Main
None
15 or 90
seconds,
as ordered
Continuous
Retry
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff). After
5 minute delay, a new trial for ignition is initiated. This sequence
continues until lightoff or “Call for Heat” is removed.
S8610H
Combination
1.0 A Pilot
and
2.0 A Main
None
15 or 90
seconds,
as ordered
Lockout
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff), and
lockout. Cycle “Call for Heat” to restart ignition sequence.
S8610M
Separate
1.0 A Pilot
and
2.0 A Main
None
15 or 90
seconds,
as ordered
Continuous
Retry
Spark and pilot gas ON until lightoff or trial for ignition ends. If
pilot fails to light, pilot gas and spark OFF (100% shutoff). After
5 minute delay, a new trial for ignition is initiated. This sequence
continues until lightoff or “Call for Heat” is removed.
S8670D
Combination
1.0 A Pilot
and
2.0 A Main
30
seconds
15 or 90
seconds,
as ordered
Lockout
After prepurge, spark and pilot gas ON until lightoff or trial for
ignition ends. If pilot fails to light, pilot gas and spark OFF
(100% shutoff), and lockout. Cycle “Call for Heat” to restart
ignition sequence.
Automatic Ignition Systems
®
ANSI Z21.20
69-1954-01
INSTALLATION INSTRUCTIONS

Honeywell S8670J Specifications

General

Brand	Honeywell
Model	S8670J
Category	Controller
Language	English