To Next Page

To Previous Page

IMPORTANT:

• Repair Condition: Connector repair is only for out of warranty.

• Repairing must operate by professional repairers (Note) in repair center, not applicable for end

user.

• Electrostatic protection is required when component replacement is required.

• The monitor meets ROHS, please use Lead-free solder wire for soldering.

• If Connector need to replace, must check specification and part number whether match the BOM

and location.

• If connector need to replace, please insert new parts carefully because the near pin may cause

short circuit by inappropriate operate.

• DO NOT allow any liquid on the board. Water and moisture may cause short-circuit to the

electronic components and lead to malfunctions.

• The fusion point of Lead-Free solder is requested. Repairing with conventional lead wire may

cause damage.

• Work quickly to avoid overheating the circuit board as soon as you confirm the steady soldering

condition.

• Keep the soldering iron tip clean and well tinned and when replacing parts.

• A close inspection of the circuit board revealed look in good condition.

• After repaired, must connect source to each port to check Main board function is ordinary.

Note: (The requirement of professional repairers’ regulation by ERP lot5)

1) The professional repairer has the technical competence to repair electronic displays and complies

with the applicable regulations for repairers of electrical equipment in the Member States where it

operates. Reference to an official registration system as professional repairer, where such system

exists in the Member States concerned, shall be accepted as proof of compliance with this point.

2) The professional repairer is covered by insurance covering liabilities resulting from its activity,

regardless of whether this is required by the Member State.

HDMI connector CN502

Repair the HDMI connector:

1) Use a soldering iron and a de-soldering pump to remove as much solder as possible from the

pin.

2) Use a hot air gun to melt the solder on the pins.

Questions and Answers:

Need help?

Do you have a question about the HP E45c G5 and is the answer not in the manual?

HP E45c G5 Specifications

General

HD type	DQHD
Panel type	VA
Color depth	8 bit
Color gamut	99 %
Pixel pitch	0.21 x 0.21 mm
Pixel density	120 ppi
Response time	3 ms
Display diagonal	44.5 \
Surface hardness	3H
Anti-glare screen	Yes
Display resolution	5120 x 1440 pixels
Native aspect ratio	32:9
Vertical scan range	48 - 165 Hz
Horizontal scan range	30 - 250 kHz
Screen curvature rating	1500R
Contrast ratio (dynamic)	8000000:1
Contrast ratio (typical)	3000:1
Display number of colors	16.7 million colors
Display diagonal (metric)	113 cm
Display brightness (typical)	400 cd/m²
Supported graphics resolutions	640 x 480 (VGA), 720 x 400, 800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 800 (WXGA), 1440 x 900 (WXGA+), 1600 x 900, 1680 x 1050 (WSXGA+), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA), 2560 x 1440, 3440 x 1440, 5120 x 1440
USB Type-A downstream ports quantity	4
Number of USB Type-C upstream ports quantity	2
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	5 - 95 %
Package depth	280 mm
Package width	1267 mm
Package height	485 mm
Package weight	22470 g
Height adjustment	150 mm
Panel mounting interface	100 x 100 mm
Feet color	Black
Country of origin	China
Market positioning	Business
RMS rated power	6 W
Sustainability certificates	ENERGY STAR, TCO
AC input voltage	100 - 240 V
AC input frequency	50/60 Hz
Power consumption (max)	275 W
Power consumption (standby)	0.5 W
Power consumption (typical)	55 W

Weight and Dimensions