HP OMEN 27k User Manual

3
● Do not get the board wet. Water and moisture can cause a short circuit that causes malfunctions.
● To avoid damage, be sure to use lead-free solder.
● When soldering, work quickly to avoid overheating the circuit board.
● Keep the soldering iron tip clean and well tinned when replacing parts.
● After repair, perform a close inspection of the circuit board to confirm it is in good condition.
● After repair, perform a function test to confirm the power supply is working properly.
ERP Lot5 requirement
1. A professional repairer must have the technical competence to repair electronic displays and comply with
the applicable regulations for repairers of electrical equipment in the Member States where the repairer
operates. Reference to an official registration system as professional repairer, where such a system exists in the
Member States, shall be accepted as proof of compliance.
2. A professional repairer must have insurance that covers liabilities resulting from repairs, regardless of
whether required by the Member State.
RoHS (2002/95/EC) requirements
Applied to all countries that require RoHS.
The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a legal
requirement by the EU (European Union) for the global electronics industry sold in the EU and other countries.
Any electrical and electronics products launched in the market after June 2006 should meet this RoHS
requirement. Products launched in the market before June 2006 are not required to be compliant with RoHS parts.
If the original parts are not RoHS complaint, the replacement parts can be non-ROHS complaint. If the original
parts are RoHS compliant, the replacement parts MUST be RoHS complaint.
If product service or maintenance requires replacing parts, confirm the RoHS requirement before replacement.
General descriptions
This manual contains general information. There are two levels of service:
Level 1: Cosmetic/appearance/alignment service
Level 2: Circuit board or standard parts replacement
Firmware updates
Firmware updates for the monitor are available at support.hp.com. If no firmware is posted, the monitor does not
need a firmware update.
Before returning the repaired product to the customer
Perform an AC leakage current check on exposed metallic parts to be sure the product is safe to operate without
the potential of electrical shock. Do not use a line isolation transformer during this check.
Measurements that are not within specified limits present a possible shock hazard. You must check and repair the
product before returning it to the customer.

HP OMEN 27k Specifications

General

Depth	52.2 mm
Width	613.6 mm
Height	364.3 mm
Weight	7540 g
Package depth	160 mm
Package width	699 mm
Package height	446 mm
Package weight	10990 g
Color depth	8 bit
Screen shape	Flat
Pixel density	163 ppi
Display diagonal	27 \
Surface hardness	3H
Anti-glare screen	Yes
Display technology	-
Native aspect ratio	16:9
Vertical scan range	55 - 144 Hz
Horizontal scan range	80 - 320 kHz
Contrast ratio (typical)	1000:1
Display number of colors	1.07 billion colors
Display diagonal (metric)	68.6 cm
Display brightness (typical)	400 cd/m²
Supported graphics resolutions	1280 x 1024 (SXGA), 720 x 400, 1280 x 800, 800 x 600 (SVGA), 1440 x 900 (WXGA+), 1600 x 900, 1024 x 768 (XGA), 1680 x 1050 (WSXGA+), 640 x 480 (VGA), 1920 x 1080 (HD 1080), 1280 x 720 (HD 720)
AC input voltage	100 - 240 V
Power supply type	Internal
AC input frequency	50/60 Hz
Power consumption (max)	120 W
Power consumption (standby)	0.5 W
Power consumption (typical)	50 W
RMS rated power	3 W
Number of speakers	2
Product color	Black
Country of origin	China
Market positioning	Gaming
HDMI version	2.0/2.1
DisplayPort version	1.4
HP segment	Home
Pivot angle	-90 - 90 °
Tilt angle range	-5 - 20 °
Panel mounting interface	100 x 100 mm
Operating temperature (T-T)	5 - 35 °C
Storage relative humidity (H-H)	20 - 80 %
Operating relative humidity (H-H)	5 - 95 %

Weight and Dimensions

Depth (with stand)	223.3 mm
Height (with stand)	523.7 mm