Icom IC-F9020 Series User Manual

2
P h d h ld
[PTT]
d k i t th
APCO P25 Mode Operation
2 Select the desired Talkgroup ID (or name)
using [CH Up]/[CH Down], or [CH Up/Down].
 NOTE: When ‘65535’ is selected as the

Talkgroup
ID All Call is an open call to
2
P
us
h
an
d h
o
ld
[PTT]
an
d
spea
k i
n
t
o
th
e
microphone.
 NOTE: Only one station is permitted to speak at a
 time.
3Release [PTT] to receive a response.
 NOTE: When the Talk-group ID is set to ‘65535,’
 any Talk-group call can be received (if NAC is
 matched)

Talkgroup
ID
,
All Call is an open call to
 everyone on your system.
3 Push and hold [PTT] to transmit the Talkgroup
call to the specific group, then speak into the
microphone.
• The Transmit indicator lights red.
• Depending on the pre-set value, the target
station does not open the squelch and
 matched)
.
Talk-group display on mode change
The Talk-group ID (or name) is displayed for 2 sec on
the upper line of the LCD when the operating
channel or zone is changed. This function can be
turned OFF by your dealer.
Talk-group display on PTT
Th T lk
g ID ( ) i dild f 2
station does not open the squelch
,
and
communication is not established, if the
Talkgroup ID or NAC (Network Access Code)
is not matched. Ask your dealer for details.
• The Talkgroup ID (or name) is displayed for
2 sec when [PTT] is pushed. (Depending on
the pre-set value.)
4 Release [PTT] to receive.
Th
e
T
a
lk
-
g
roup
ID (
or
name
) i
s
di
sp
l
aye
d f
or
2
sec
on
the upper line of the LCD when [PTT] is pushed.
This function can be turned OFF by your dealer.
■ Pager function
Transmitting
This function can be used as a “message pager” to
fi th t t t ti f ll ’ id tifi ti
Receiving
1 When a Talk-group call is received;
• The Busy indicator lights green.
• The ringer sounds. (Depending on the pre-
setting.)
• The Talk-group ID (or name) and calling
station ID (or name) are displayed for 2 sec.
con
fi
rm
th
e
t
arge
t
s
t
a
ti
on
o
f
a
ca
ll
er
’
s
id
en
tifi
ca
ti
on,
even when the operator leaves the transceiver
temporarily unattended. If the target station is active
when receiving a signal, an acknowledgement
is automatically transmitted. The caller station can
verify whether a target station is active or not.
[Digital Button] or [Digital Page] key assignment is
(Depending on the pre
-
set value.)
“ALL CALL” is displayed instead of the Talkgroup
ID (or name) when All Call is received.
• Depending on the pre-set value, the transceiver
does not open the squelch, and communication is
not established, if the Talk-group ID or NAC
(Network Access Code) is not matched.
necessary to transmit the pager signal.
1 Push [Digital Button] to enter the digital call
model selection mode.
 ✔ Quick access
 Push [Digital Page] to directly enter the Individual
 ID selection mode. In this case, skip step 2.
The talkgoup ID
46
The calling station
name ( or ID )

Icom IC-F9020 Series Specifications

General

Brand	Icom
Model	IC-F9020 Series
Category	Transceiver
Language	English