Indesit IDS 105 User Manual

GB
3
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
• The socket is earthed and complies with current
regulations.
• Thesocketcanwithstandthemaximumloadofthe
appliance, which is indicated on the data plate located
on the inside of the door (see chapter entitled Description
of the appliance).
• Thepowersupplyvoltagefallswithinthevaluesindicated
on the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
the plug (see After Sales Service); do not use extension
cables or multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in
order to prevent all potential hazards. (See After Sales Ser-
vice)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt
(see chapter entitled Rinse aid and refined salt) . The water
may overflow: this is normal and is not a cause for concern.
Select the water hardness value (see chapter entitled Rinse
aid and refined salt) . - After the salt has been poured into
the machine, the LOW SALT indicator light* switches off.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.
Technical data
Dimensions
width 45 cm
height 85 cm
depth 60 cm
Capacity 10 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 psi – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/CE Waste Electrical
and Electronic Equipment (WEEE)
ECODESIGN REGULATION
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a nor-
mal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption
even further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
** Data is obtained by recording values when the appliance is operational and loaded with user crockery.
Standard conditions* User conditions**
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration
(min/cycle)
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration (min/
cycle)
INTENSIVE
1,30 14 150 1,15 14 140
NORMAL
1,05 14 115 0,95 13 110

Indesit IDS 105 Specifications

General

Style	Free-Standing
Color	White
Load Capacity	12 Place Settings
Number of Cycles	5
Cycle Selections	Rinse Only
Options/Settings	13
Drying Type	Residual
Temperature Options	45-70°C
Noise level	53 dB
Special Features	Child Lock
Energy Class	A
Annual Energy Consumption	-
Energy Consumption Per Cycle	-
Annual Water Consumption	-
Water Consumption Per Cycle	10 L
Voltage	-
Frequency	-
Current	-

Weight and Dimensions

Depth	600 mm
Height	850 mm
Width	450 mm
Net Weight	-