Input and Output
• Audio inputs : 1 Analog, 1 Optical,
Bluetooth, USB
• HDMI Video Inputs : 3
• HDMI Video Output
(with Audio Retur
n Channel) : 1
• HDMI HDCP Version : 2.2
Bluetooth specication
• Bluetooth Version : 4.2
• Max Bluetooth Range : 32 ft (10m)
• Bluetooth Prole : A2DP V1.3 / AVRCP V1.6
USB specication
(USB) port: Type A
File Format Type Compatibility list:
Extension Codec
Sampling
Rate
Bitrate
*.mp3
MPEG 1
Layer2
16KHz ~
48KHz
80kbps~320kbps
MPEG 1
Layer3
16KHz ~
48KHz
80kbps~320kbps
MPEG 2
Layer3
16KHz ~
48KHz
80kbps~320kbps
MPEG 2.5
Layer3
16KHz ~
48KHz
80kbps~320kbps
*.wav -
16KHz ~
48KHz
up to 3000kbps
Product dimension and weight
• Soundbar Dimensions (W x H x D) : 1018 x 58 x 78 (mm) \
40"x2.3"x3"
• Soundbar Weight : 2.3kg \ 5.1lbs
• Subwoofer Dimensions (W x H x D) : 440 x 305 x 305 (mm) \
16" x 12" x 12"
• Subwoofer Weight : 12.1kg \ 26.7lbs
• Packaging Dimensions (W x H x D) : 1097 x 365 x 450 (mm) \
43.2" x 14.4" x 17.7"
• Packaging Weight (Gross) : 17.85kg \ 39.4 lbs
Wireless transmitter/receiver section
• Bluetooth Frequency Range : 2402MHz-2480MHz
• Max Transmitting power : 9dBm (EIRP)
• Bluetooth Transmitter modulation : GFSK, π/4 DQPSK,
8DPSK
• 5.8G Wireless Frequency Range : 5740MHz-5840MHz
• 5.8G Max Transmitting power : 20dBm (EIRP)
10. TROUBLESHOOTING
If you have problems using this product, check the following points
before you request service.
System
The unit will not turn on.
• Check if power cord is plugged into the outlet and the soundbar
Sound
No sound from Soundbar.
• Make sure that the soundbar is not muted.
• On the remote control, select the correct audio input source
• Connect the audio cable from your soundbar to your TV or other
devices.
• However
, you do not need a separate audio connection
when:
– the soundbar and TV are connected through HDMI ARC
connection, or
– a device is connected to the HDMI IN connector on your
soundbar.
• Reset your soundbar to its factory settings via press and hold
VOLUME -, VOLUME+ and SOURCE button on soundbar top
panel
Sound is strange after sound setting adjustment
• Reset audio setting by press and hold SOUND button on remote
control for 5 seconds
No sound from the wireless subwoofer.
• Check if the Subwoofer LED is in solid white colour. If white LED
is blinking, connection is lost. Manually pair the Subwoofer to
soundbar (see ‘Pair with the subwoofer’ on page 4).
Distorted sound or echo.
• If you play audio from the TV through the soundbar, make sure
that the TV is muted.
Audio and video are not synchronized.
• Press AUDIO SYNC +/- to synchronize the audio with the video.
Error message is displayed on the display panel.
• When “ERROR” is displayed, it indicates that an input audio
format is not supported.
• When “ERROR” is displayed in USB source, it indicates that the
connected USB device or Audio le is not supported
Video
If there is no picture on the TV Screen
• Check that the soundbar power is ON, the intended source is
ON, and the input is set correctly on the soundbar.
Bluetooth
A device cannot connect with the Soundbar.
• You have not enabled the Bluetooth function of the device. See
the user manual of the device on how to enable the function.
• The soundbar is already connected with another Bluetooth
device. Press and hold BT button on your remote control to
disconnect the connected device, then try again.
• Turn off and turn off your Bluetooth device and try to connect
again.
• The device is not correctly connected. Connect the device
correctly.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
