EN
31
USING MENUS FOR DETAILED ADJUSTMENT
CLOCK ADJ.
Allows you to set the current date and time (墌 pg. 10).
DSC (GR-D90/D70 only)
QUALITY , IMAGE SIZE
Refer to “Picture Quality/Image Size Setting”
(墌 pg. 11).
REC SELECT
[ ]: When Snapshot recording is performed
with the VIDEO/DSC Switch 4 set to “VIDEO”, still
images are recorded only onto the tape.
/ : When Snapshot recording is
performed with the VIDEO/DSC Switch 4 set to
“VIDEO”, still images are recorded not only onto the
tape but also on the memory card (640 x 480 pixels).
In this mode, the “SNAP MODE” selection in the
CAMERA Menu is also applicable to memory card
recording.
VIDEO
SOUND MODE
........ 墌 pg. 32, “Playback Sound”.
12BIT MODE
........ 墌 pg. 32, “Display”.
REC MODE
Allows you to set the tape recording mode ([SP] or
LP) depending on your preference (墌 pg. 10).
It is recommended you use “REC MODE” in the
“ VIDEO” Menu when using this camcorder as a
recorder during dubbing (墌 pg. 33, 34).
•“REC MODE” can be set when the Power Switch y is
set to “PLAY” or “ ” (墌 pg. 10, 28).
COPY
(GR-D90/D70 only)
ON: Enables dubbing of images recorded on a tape
to a memory card (墌 pg. 21).
[OFF]: Enables snapshots to be taken during tape
playback.
S/AV INPUT
(GR-D90/D70 only)
ON: Enables audio/video signal input from the AV and
S-VIDEO connectors (墌 pg. 33).
[OFF]: Enables audio/video signal output to a TV,
VCR, etc. via the AV and S-VIDEO connectors
(墌 pg. 16, 33).
• When “S/AV INPUT” is set to “ON”, camcorder
playback cannot be viewed on the AV output.
–
RETURN
–
–
DSC
TYQUAL I
REC SELECT
FINE
021X7486
IMAGE SIZE
–
–
–
–
–
IVDE
O
MDOESOUND
MDOE
12
BIT
ODEREC M
COPY
STEREO
SOUND
1
OFF
OFF
NPUT
S/
AV I
RETURN
MELODY
EEPB
–
RETURN
AM RE SE TC
LCD
RIORITYP
–
ON
EMO MODED
–
ON
EMOTER
–
ON
ALLYT
–
SYSTE
M
For Playback Menu
1 Set the VIDEO/DSC Switch 4 to “VIDEO” (GR-D90/
D70 only), then set the Power Switch y to “PLAY”
while pressing down the Lock Button t located on the
switch.
2 Press the MENU/VOLUME wheel % in. The Menu
Screen appears.
3 Rotate the MENU/VOLUME wheel % to select the
desired function menu, and press it.
4 Rotate the MENU/VOLUME wheel % to select the
desired function, and press it to display the Sub Menu.
5 Rotate the MENU/VOLUME wheel % to select the
desired parameter and press it. Selection is complete.
6 Rotate the MENU/VOLUME wheel % to select
“ RETURN” and press it twice to close the Menu
Screen.
SYSTEM
Each setting is linked with “ SYSTEM”, which
appears when the Power Switch y is set to “ ”
(墌 pg. 30).
The parameters are the same as in the description on
pg. 30.
[ ] = Factory-preset
1 GR-D90/70/30US EN 23-34 02.11.6, 3:13 PM31
To Next Page
Loading...
Need help?
General
