JVC GR-DVA10 User Manual

SELECT SCENES
ihn Anes Point the remote control at the camcorder's remote
Editing Menu sensor. Press PLAY (b) and then press R.A.EDIT ON/
OFF on the remote control.
The Random Assembie Editing Menu appears.
fee if using a FadeMipe at the beginning of the scene,
FO) press FADE/WIPE on the remote control.
*#Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed,
* You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
149 Nhe beginning ofthe scene, press EDIT IN/OUT on
93 the remote control. The Edit-In position appears in
the Random Assemble Editing Menu.
‘At the end of the scene, press EDIT IN/OUT. The
Edit-Out position appears in the Random Assemble
Editing Menu.
If using a Fade/Wipe at the end of the scene, press
FADE/WIPE.
*Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
*1f you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
* You cannot use a Picture Wipe/Dissolve at the end
of the last scene.
*When you use Fade/Wipe effects, that time is
included in the total time (this does not apply to
Picture Wipe/Dissolve).
If using Playback Special Effects, press EFFECT
(F pp. 43),
f/f] Repest steps 6 through 9to register additional scenes.
‘To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
‘If you are not using Fade/Wipe or Program AE with
special effects, repeat steps 6 and 7 only.
NOTES:
‘© When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between
them.
© If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be
canceled and editing will not take place.
© if there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in
the edited version
Since time codes register time only as accurately as seconds, the time code total time may not match the
total program time exactly.
© Turning off the camcorder’s power erases all registered Edit.In and Edit-Out points.
Ifyou select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or
Black & White Fader. in this case the Dissolve or Black & White indicator begins blinking. Once the next
Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during
recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.
© ‘tis not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble
Editing using a DV cable.
Remote Sensor
ee ve
AUTOMATIC EDITING TO VCR
Hf | Rewind the tape in the camcorder tothe beg
the scene you want to edit and press PAUSE (11).
GPA Point the remote contro! towards the VCR's remote
fad sensor and press VCR REC STBY (@12), or manually
‘engage the VCR's Record-Pause mode.
B Press the Recording Start/Stop Button on the
Pi) camcorder. Editing proceeds as programed, right
through to the end of the last registered scene.
‘* Pressing START/STOP on the remote control does
not start editing.
‘When dubbing is complete, the camcorder enters
the Pause mode, and the VCR enters its Record-
Pause mode.
‘If you do not register an Edit-Out point, the tape will
be dubbed all the way to the end automatically.
If you operate the camcorder during automatic
editing, the VCR will enter its Record-Pause mode
and automatic editing will stop.
FE] Engaze the Stop modes forthe camcorder and the
VCR.
To make the R.A.Edit counter display disappear, press
R.A.EDIT ON/OFF on the remote control.
NOTES:
‘© Pressing RA.EDIT ON/OFF on the remote control clears
all settings registered during Random Assemble Editing.
‘© When the editing cable is connected to the remote
control's Pause In connector during dubbing, make sure
the remote control is pointed at the VCR's sensor, and
the path between the two is unobstructed.
© Random Assemble Editing may not function properly
when using a tape including several duplicated time
codes (CF pg. 19).

JVC GR-DVA10 Specifications

General

Brand	JVC
Model	GR-DVA10
Category	Camcorder
Language	English