JVC GR-DVA10 User Manual

slats
16. The picture wipe function
does not work.
16 * The Slow Shutter mode is
activated.
= “WIDE MODE" is not set to
“OFF”.
16. * Disengage the Slow Shutte
mode or set “WIDE MODE"
to “OFF” before preparing
to use the Picture Wipe
( pg. 24, 26, 28).
17. Scene transition does not
go as expected.
17. «When using “Picture Wipe/
Dissolve” (C7 pg. 26), there
is a delay of a fraction of a
second between the
previous record stop-point
and the Dissolve start-point.
This is normal, but this slight
delay becomes especially
noticeable when shooting
fast-moving subject or
during rapid panning.
(24. During recording, the date/
time does not appear.
“OFF” in the Menu Screen,
+ Self-Recording is performed.
24. #Set “DATE/TIME” to “ON”
in the Menu Screen
(CF pg, 25),
+ During Self-Recording, the
datehime does not appear
(CF pg. 15).
25, The indicators and
messages do not appear.
“ON SCREEN” is set to
“SIMPLE” or “TIME CODE”
is set to “OFF” in the Menu
Screen.
25, # Set “ON SCREEN’ to “LCD”
or “LCD/TV" and set
“TIME CODE” to “ON”
in the Menu Screen
(© pg. 25, 32).
18. The Video Echo mode
does not work,
18. * The Picture Wipe or
Dissolve functions are in use.
* “WIDE MODE" is set to
“SQUEEZE” in the Menu
Screen.
© A Fade-In or Fade-Out is in
progress.
18. # Set “WIDE MODE" to
“CINEMA” or “OFF” mode
(CF pg. 24),
* Do not try to use the Video
Echo mode during a Fade-In
or Fade-Out CF" pg, 26, 28).
79. Even when Slow Shutter is
not selected, the image
looks like itis activated.
19 *When shooting in the dark,
the unit becomes highly
sensitive to light and the
image takes on an effect
similar to Siow Shutter.
79, # f you want the lighting to
look more natural, set GAIN
UP to “AGC" or “OFF” in
the Menu Screen
(pg. 23).
26, Images on the LCD
monitor appear dark or
whitish.
». * In places subject to low
temperature, images become
dark due to the characteristics
of the LCD monitor. When
this happens, the displayed
colors differ from those that
are actually recorded. This is
not a defect of the camcorder.
*When the LCD monitor's.
fluorescent light reaches the
end of its service life,
images on the LCD monitor
become dark. Consult your
nearest JVC dealer.
26, # Adjust the brightness and
angle of the LCD monitor
(F pg. 14, 15).
20. There is no strobe when
the Classic Film or Strobe
mode is activated.
20. # The Picture Wipe or
Dissolve function is in use.
20, * Do not try to use the Classic
Film or Strobe mode during
a scene transition
(> pg. 26, 28).
27. The rear of the LCD
monitor is hot.
27. «The light used to illuminate
the LCD monitor causes it to
become hot.
27, © Close the LCD monitor to.
turn it off or set the Power
‘Switch to “OFF”, and let the
unit cool down.
28. The indicators and the
image color on the LCD
monitor are not clear.
28. «This may occur when the
surface or the edge of the
LCD monitor is pressed.
21. White Balance cannot be
activated.
21. ¢ The Sepia or Monotone
mode is activated.
21, # Turn off Sepia or Monotone
before setting White
Balance ( pg. 28, 30).
22, When shooting a subject
illuminated by bright light,
vertical lines appear.
22, «This is a result of exceed-
ingly high contrast, and is
not a malfunction.
22,
23. When the screen is under
direct sunlight during
shooting, the screen.
becomes red or black for
an instant.
is not a malfunction.
29. The LCD monitor or
viewfinder indications
blink.
29. * Certain FadeWipe effects,
Certain modes of Program AE
with special effects, “DIS”
and other functions that
Cannot be used together are
selected at the same time.
29. © Re-read the sections
covering Fade/Wipe effects,
Program AE with special
effects and “DIS”
(F pg. 24, 26 - 28).
CONTINUED ON NEXT PAGE

JVC GR-DVA10 Specifications

General

Brand	JVC
Model	GR-DVA10
Category	Camcorder
Language	English