Kenwood 1080VR User Manual

Remote control unit
The backlight flashes five times during nor-
mal operation.
Subwoofer volume cannot be adjusted.
Certain inputs cannot be selected using
the remote control.
Remote control operation is not possible.
Do
not
use
contact
cleaning
agents
because
they
could
cause
a
malfunction.
Be
specificall
containing
oil,
since
they
may
deform
the
plastic
components.
Note
For the U.S.A.
FCC WARNING
This
equipment
may
generate
or
use
radio
frequency
energy.
Changes
or
modifications
to
this
equipment
may
cause
harmful
interference
unless
the
modifications
are
expressly
approved
in
the
instruction
manual.
The
user
could
jose
the
authority
to
operate
this
equipment
if
an
unauthorized
change or modification 1s made.
NOTE:
Tn.s
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
Part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
ins
interference
to
radio
communications,
if
it
is
not
installed
and
used
in
accordance
with
the
instructions.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
-
-
Reorent
or
relocate
the
receiving
antenna
The batteries are nearing exhaustion.
Subwoofer is OFF.
No preset codes registered at for the respec-
tive input(s).
The remote control is set to a different opera-
tion mode.
Batteries are exhausted.
The remote control unit is too far away from
the main system, controlling angle is too large,
or there is an obstacle between the receiver
and the remote.
The audio cords and system control cords are
not connected properly.
No software is loaded in the source compo-
nent.
An attempt is made to play a tape which is
being recorded in the cassette deck.
The
remote
control
has
not
been
set
to
the
operation
mode
for
the
component
you
wish
to
control.
— —
Increase
tne
separation
between
the
equipment
and
receiver.
~~
Connect
the
equipment
into
an
outiet
on
a
circuit
different
from
that
to
which
the
receiver
is
connected.
-~
Consult
the
dealer
or
an
experienced
radio
/
TV
technician
for
help.
tallation. This equipment may cause harmful
10B0VR (En/K}
Replace with new batteries to preserve the
currently registered setup information.—2@.
Turn the subwoofer ON.
Register a preset code or Non-iR code at the
respective input(s). 36
Press VIDEO, AUDIO, or TV to select the
approriate operation mode.
Replace with new batteries. If the backup-is
exhasted before you can replace the batter-
ies, redo the setup procedure. —2i4 ~ 36
Operate the remote control unit within the
controllable range.
Connect properly referring to “Setting up the
system”. -=
Place software in the source component you
want to play.
Wait until recording has completed.
Press the VIDEO, AUDIO, or TV key to activate
the operation mode for the component you
want to control before operation. - (32,
y careful against using contact cleaning agents
Memory back up function
Please
note
that
the
following
items
will
be
deleted
from
the
unit's
memory
if
the
power
cord
is
disconnected
from
the AC outlet for approximately 3 days.
pe Power mode
*
Settings
made
using
OSD
(like
SURROUND
SET
UP)
* Input selector settings
* Volume ievel
© Broadcast band.
le Frequency setting.
* Preset stations.
For the U.S.A.
Note to CATV system installer:
This
reminder
is
provided
to
call
the
CATV
system
installer’s
attention
to
Article
820-40
of
the
NEC
that
provides
guidelines
for
proper
grounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building,
as
close
to
the
point
of
cable
entry
as
practical.

Kenwood 1080VR Specifications

General

Brand	Kenwood
Model	1080VR
Category	Stereo Receiver
Language	English