Why is the stapling position not as expected on my Konica Minolta bizhub C650?
If the stapling position is not as expected on your Konica Minolta All in One Printer, the orientation setting may not be correct. Check the stapling position in the printer driver setup dialog box.
Why does a postscript error appear on my Konica Minolta bizhub C650 All in One Printer?
If a postscript error appears on your Konica Minolta All in One Printer, it may be due to insufficient computer memory. Try performing a test print to check if printing is possible.
What to do if Konica Minolta bizhub C650 All in One Printer shows no response?
If your Konica Minolta All in One Printer shows 'No response' when trying to communicate with the center, try communicating with the center again. Also, check the communication environment on the center side.
What to do if Konica Minolta bizhub C650 shows busy line?
If your Konica Minolta All in One Printer displays a 'Busy line' error when trying to communicate, attempt to communicate with the center again.
What to do if the message 'Failed to register' appears on Konica Minolta Printer Accessories?
If the message “Failed to register” appears on the Konica Minolta Printer Accessory, it could be due to the limited scanning time. To resolve this, refer to the Quick Guide Authentication Unit (Biometric Type AU-101) for guidance on positioning your finger correctly for scanning. Ensure your finger is correctly placed and remains still during scanning. If your finger is dirty or chapped, wash your hands or address the chapping. Also, ensure the finger width is within the range of 10 mm to 25 mm; adjust the finger position if necessary.
Why can't I select a printer driver setting on my Konica Minolta bizhub C650 All in One Printer?
A printer driver setting cannot be selected on your Konica Minolta All in One Printer because some functions cannot be combined. Do not try to select settings that are not available.
Why can't stapling be performed on my Konica Minolta All in One Printer?
Stapling cannot be performed on your Konica Minolta All in One Printer if there are a large number of pages to be printed; change the number of pages. Also, stapling is not possible if the document contains pages of different sizes; check the document.
What does the 'Conflicts' message mean on my Konica Minolta bizhub C650 All in One Printer?
If you see a "Conflicts" message with "Unable to Select" or "Function Canceled" on your Konica Minolta All in One Printer, it means an incorrect combination of functions has been specified. Check the settings and specify the functions correctly.
Why can't I print the watermark on my Konica Minolta All in One Printer?
If the watermark cannot be printed on your Konica Minolta All in One Printer, check the watermark settings to ensure they are correctly set. Also, verify the density settings, as a density that is too low may prevent the watermark from printing. Note that watermarks cannot be printed in graphics applications.
What to do if Konica Minolta bizhub C650 shows 'No printers are connected' or 'Print error'?
If you see a "No printers are connected" or "Print error" message on your Konica Minolta All in One Printer, it could be due to several reasons. First, verify that the printer name selected is compatible with the printer controller. Also, ensure that the network or USB cable is properly connected. Check the machine's control panel for any errors. Insufficient memory space may also cause this issue; in this case, perform a test print to see if printing is possible.
General| Print Speed (Color) | 65 ppm |
|---|---|
| Print Speed (Black) | 65 ppm |
| Copy Resolution | 600 x 600 dpi |
| Scan Resolution | 600 x 600 dpi |
| Printing Technology | Laser |
| Duplex Printing | Yes |
| Type | Color |
| Monthly Duty Cycle | 300000 pages |
| Supported Paper Sizes | Letter, Legal, A4, A5, B5 |
| Connectivity | USB, Ethernet |
| Operating System Compatibility | Windows, Mac |
To Next Page