Krups EA80 User Manual

98
ENGLISH
If you unplug the appliance during cleaning. press the button, or there is an
electrical power cut, the cleaning program will start again from the beginning. In
this case, another cleaning tablet may be necessary. Make sure to carry out the
full cleaning cycle to ensure good maintenance of your appliance. The cleaning
cycle is intermittent: do not put your hands under the water outlets ‘E’ and ‘W’
while the cycle is in progress.
Only use KRUPS fXS300Q) cleaning tablets. We cannot be held responsible for any damage
that may result from the use of tablets from other brands.
You can obtain cleaning tablets from KRUPS Service Centres.
Scale removal program - total duration: about 20 minutes
The quantity of scale deposited depends on the hardness of the water used. The appliance
will automatically warn you by the ‘CALC’ light coming on when you need to proceed with
scale removal.
This program is only accessible when the appliance requests it.
To benefit from the guarantee conditions, it is essential to perform the appliance’s
scale removal cycle when informed to do so. Be sure to follow the procedure closely
step by step. You can continue to use the appliance when the light is on. but you are
advised to perform the program as soon as possible.
If your appliances tted with our Claris - Aqua Filter System F088 cartridge, please remove
the cartridge during the descaling operation.
Only use KRUPS scale removal products. You can obtain scale removal products from
KRUPS Service Centres.
We cannot be held responsible for any damage that may result from the use of tablets from
other brands.
Ensure your work surface is protected during cleaning and scale removal cycles,
especially if it is made of marble, stone or wood.
Start the descaling program by pressing the
button. The ‘CALC’ light becomes constant
and the indicator lights
and ash.
Remove and clean the drip tray.
Place a container with a minimum capacity of 0.6L under the coffee outlets as well as under
the steam nozzle - Fig. 24. Empty the tank and rell it with warm water up to the line ‘CALC’
- Fig. 33.
Dissolve a sachet of Krups (40 g) F054 descaler in the tank - Fig. 33.
Replace the water tank. The indicator light
switches off.
Press the button after carrying out all of these operations.
The first phase (approximately 8 min) begins.
The descaling cycle will start automatically.
At the end of this phase, the appliance beeps every 10 seconds and the indicator
light
ashes.
Empty the used water container and put it back in place.
Empty and rinse the water tank - Fig. 34.
Rell the tank with water and put it back into place. The warning light
goes out.
Press the button
again to start the second phase. The sound signal stops.
The second phase (about 6 min) begins.
The program continues. It rinses the appliance and removes any traces of the
descaler.
At the end of this phase, the sound signal beeps every 10 seconds Remove and
empty your used water container and put it back in place.
Press the
button again to start the nal phase. The sound signal stops.
The nal phase (approximately 6 min) begins.
The program continues. It removes the last particles of descaler.
When the descaling cycle is nished, the indicator light ‘CALC’ goes out.
Rell your water tank.
Your appliance is ready for the next use.
If there is not enough water in the water tank, you will be warned by the light.
Add the appropriate amount of water to the tank and scale removal will continue
automatically.
If you unplug the appliance during cleaning, press the button, or there is an electrical
power cut, the cleaning program will start again from the beginning. In this case, another
cleaning tablet may be necessary. Make sure to carry out the full cleaning cycle to ensure
good maintenance of your appliance.
The cleaning cycle is intermittent: do not put your hands under the water outlets ‘E’ and
‘W’ while the cycle is in progress.
Long rinsing program - total duration: about 2 minutes
When it is necessary to make a long rinsing program, the appliance warns you of this by
ashing the ‘CLEAN’ and ‘CALC’ lights.
Remove, ll and replace the water tank.
Place a container with a minimum capacity of 0.6L under the coffee outlets and the steam
nozzle.
Start the long rinsing program by pressing the button. The lights ‘CLEAN’ and ‘CALC’
become constant and the indicator light starts ashing.
When the long rinse is nished, the lights ‘CLEAN’ and ‘CALC’ go out and the indicator
light becomes constant.
Your appliance is ready for the next use.
The appliance can ask you to empty the coffee ground collector.
OTHER FUNCTIONS
To switch the appliance off
You can switch off your appliance at any time. As the appliance is switching off, a double
beep is emitted and all of the red lights ash, one after the other. The appliance has
registered your request and will stop as soon as possible.
Installation of the filter cartridge - total duration: around 2 min
To get the best taste from your coffee and extend your appliance’s service life, we advise
you to use only the Claris - Aqua Filter System cartridge sold as an accessory.
Fig. 30: Mechanism to indicate the month the cartridge was tted and when to replace it
(after 2 months at most).
Installing the cartridge in the appliance. On rst use, screw the lter cartridge into the
bottom of the water tank - Fig. 31. Place a 0.6L container under the steam nozzle.
Press the button tor more than 3 seconds (unless the appliance requires a ‘CLEAN’
and/or ‘CALC’ maintenance). The indicator light ashes.
When the installation of the lter cartridge is nished, the indicator light becomes
constant.

Krups EA80 Specifications

General

Brand	Krups
Model	EA80
Category	Coffee Maker
Language	English