LOVATO ELECTRIC ADXN Series

To Next Page

I651 GB 03 22 31100488

LOVATO ELECTRIC S.P.A.

24020 GORLE (BERGAMO) ITALIA

VIA DON E. MAZZA, 12

TEL. +39 035 4282111

E-mail info@

LovatoElectric.com

Web www.

LovatoElectric.com

ADXN...

SOFT STARTER

Instructions manual

WARNING!

– Read the manual carefully before installation and use.

– These devices must be installed by qualified personnel, in compliance with current plant-engineering regulations, in order to avoid damage toi persons or property.

– Before any maintenance operation on the device, switch off power supply from measuring and supply inputs.

– The manufacturer assumes no responsibility for electrical safety in the event of improper use of the device.

– The products described in this document are subject to updates or modifications at any time. Data and descriptions in the catalogue therefore do not have any contractual value.

– The building’s electrical system must incorporate a switch or circuit breaker. It must be installed close to the equipment and within easy reach of the operator. It must be marked as the disconnecting device of the

equipment: IEC/EN/BS 61010-1 § 6.11.3.1.

– Clean the instrument with a soft cloth. Do not use abrasives, liquid detergents or solvents.

CONTENTS Page

1. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. General characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. Frontal layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4. Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

5. Starting and stopping ramps management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5.1 Parameters for the management of the starting and stopping ramps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5.2 Management of starting ramps with current limit (only for ADXNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

6. Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7.1 Enabling the phase sequence control (ADXNB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7.2 Motor thermal overload protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7.3 Soft starter thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

8. Parameters setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

8.1 Setting of parameters with potentiometers (ADXNB, ADXNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

8.2 Setting of parameters with NFC (ADXNF, ADXNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

8.3 Setting of parameters with IR optical port (ADXNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

8.4 Suggested settings for typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

9. Parameters table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

9.1 Parameters menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

9.2 ADXNF parameters table (NFC version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

9.3 ADXNP parameters table (advanced version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10. Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10.1 Alarms properties table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

10.2 Alarms description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

11. Programmable outputs function table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

11.1 Programmable outputs default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

12. Optional RS485 communication (for ADXNP only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

12.1 Modbus address table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

12.1.1 Measures available on the Modbus protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

12.1.2 Start and Stop commands via Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

12.1.3 Parameters setting via Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

13. Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

14. Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

15. Mechanical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

16. Terminal layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

17. Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

18. Number of starts per hour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

19. Choosing the soft starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

20. Coordination tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

20.1 Coordination with line contactor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

20.2 Coordination with thermal overload relay (ADXNB... and ADXNF...) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

20.3 Type 1 coordination with motor protection circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

20.4 Type 2 coordination (IEC/EN/BS 60947-4-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

20.5 Coordination according to UL60947-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

21. Technical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Main Page

Need help?

Do you have a question about the LOVATO ELECTRIC ADXN Series and is the answer not in the manual?

The Lovato Electric ADXN series soft starters are designed for the gradual control of motor starting and stopping, offering a compact, simple, and quick-to-configure solution for various applications such as pumps, fans, conveyor belts, and compressors. These devices are available with rated currents ranging from 6 to 45A.

Function Description

The ADXN soft starters operate using voltage ramps, gradually increasing the voltage from a user-defined starting value (30% to 80% of the line voltage Ue) up to 100% of the line voltage within a set acceleration time. An integrated bypass relay closes once full voltage is reached. A similar behavior applies to the deceleration ramp if enabled, allowing for a controlled stop.

Three versions are available:

Basic version (ADXNB): This version offers fundamental soft starter functions, focusing solely on gradual motor starting and stopping. Configuration is straightforward, requiring adjustment of only three parameters (starting voltage, acceleration ramp, and deceleration ramp) via potentiometers on the front panel. It includes two fixed-function relay outputs.
NFC version (ADXNF): Equipped with Near Field Communication (NFC) connectivity, this version allows programming via a smartphone and the LOVATO NFC App. While default settings are optimized for scroll compressors, the NFC capability provides flexibility to adapt parameters for other loads like pumps or fans. Digital parameter setting ensures accuracy and repeatability, with the option to save configurations on the smartphone for transfer to other ADXNF units. A password protection feature safeguards settings against unauthorized tampering. This version also features two programmable relay outputs.
Advanced version (ADXNP): This comprehensive version includes all features of the ADXNF, plus integrated current transformers for motor thermal overload protection and current-limiting starting ramps that adapt to load variations. It offers both front-panel potentiometers for basic parameter adjustments and NFC connectivity for advanced parameter programming via the LOVATO NFC App. Advanced parameters include motor rated current, tripping thermal class, password, protection thresholds, tripping delays, communication settings, relay output functions, and alarm properties. An optical port on the front allows connection of optional USB (CX01) and Wi-Fi (CX02) devices for programming, data download, and diagnostics from a PC or App. Additionally, the ADXNP can be fitted with an optional RS485 communication module (CX04) for integration into remote control and supervision systems. This version also includes two programmable relay outputs.

Important Technical Specifications

Controlled phases: 2-phase control for all versions.
Built-in bypass: Yes, for all versions.
Adjustable current limit: Only for ADXNP.
Electronic motor thermal overload protection: Only for ADXNP.
Protection against phase loss: Yes, for ADXNF and ADXNP.
Protection against phase inversion: Yes, for ADXNF and ADXNP (optional for ADXNB).
Protection against locked rotor: Yes, for ADXNF and ADXNP.
Protection against thyristor overtemperature: Yes, for all versions.
Protection against low load: Yes, for ADXNF and ADXNP.
Signaling of load too high (max torque): Yes, for ADXNF and ADXNP.
Programmable alarm properties: Yes, for ADXNF and ADXNP.
Start digital input: Yes, for all versions.
Relay outputs: 2 (fixed function for ADXNB, 2 programmable for ADXNF/ADXNP).
Potentiometers for basic parameters: Yes, for all versions (can be overridden via NFC for ADXNF/ADXNP).
NFC connectivity for programming: Yes, for ADXNF and ADXNP.
IR optical port for configuration and monitoring: Yes, for ADXNP.
RS485 Modbus RTU module: Optional for ADXNP.
Rated soft starter current (le): 6 to 45A.
Rated mains input voltage: 208 to 600VAC.
Rated mains frequency: 50/60Hz auto-configuring.
Auxiliary supply voltage (Us): 24VAC/DC (ADXN...24 version) or 100-240VAC (ADXN... version).
Starting type: Voltage ramp for ADXNB/ADXNF; voltage ramp with current limitation for ADXNP.
Stopping type: Free wheel or controlled stop with deceleration ramp.
Digital input: 1 for motor start command.
Status LEDs: POWER (green - auxiliary power supply presence), RUN (green - flashing for ramp in progress, steady for full voltage), ALARM (red - active alarm, flashes indicate alarm type).
Operating temperature: -20 to +40°C (up to 60°C with current derating).
Storage temperature: -30 to +80°C.
IP protection degree: IP20.
Mounting: Screw fixing or 35mm DIN rail (IEC/EN/BS 60715).
Optional fan: Available for sizes up to 30A (EXP8007) to increase starts per hour; built-in for 38A and 45A sizes.
Optional rigid connection: For soft starters from 6 to 38A for direct mounting to SM1R motor protection circuit breakers.

Usage Features

Simple Configuration: The ADXNB offers quick setup via three potentiometers. The ADXNF and ADXNP leverage NFC for intuitive smartphone-based programming, even when the device is powered off.
Flexible Parameter Adjustment: Starting voltage (30-80% Ue), acceleration ramp time (1-20s), and deceleration ramp time (0-20s) are adjustable. The ADXNP also allows for current limit settings during starting.
Motor Protection: The ADXNP provides comprehensive motor protection including thermal overload, phase loss/inversion, locked rotor, and low load detection.
Alarm Management: Alarms are indicated by a flashing red LED, with the number of flashes identifying the specific alarm type. Alarms can be configured for automatic or manual reset, and some can trigger a motor stop or deceleration.
Remote Control and Monitoring: For ADXNP, the optional CX04 RS485 module enables Modbus RTU communication for remote supervision, command, and monitoring via PLC, HMI, or PC software.
Coordination Tables: The manual provides detailed coordination tables for selecting appropriate line contactors, thermal overload relays, and motor protection circuit breakers to ensure safe and compliant operation.
Start/Stop Commands via Modbus: For ADXNP with CX04, motor start/stop commands can be sent via Modbus, provided the ST input is continuously closed as a safety measure.

Maintenance Features

Safety Precautions: Always switch off the power supply before any maintenance. Installation should be performed by qualified personnel in compliance with regulations.
Cleaning: The instrument should be cleaned with a soft cloth; abrasives, liquid detergents, or solvents should not be used.
Troubleshooting: The ALARM LED provides visual cues for active alarms, with the number of flashes indicating the alarm type, aiding in quick diagnosis. Detailed alarm descriptions and reset procedures are provided in the manual.
Software Updates: The LOVATO NFC App and Xpress software (for ADXNP) can be used to update drivers and manage device parameters.