This manual describe the operations for a correct installation of LINE. The tubular motors with electronic limit switch LINE series are suitable to command
pergolas. The technical characteristics are provided on the label stuck on motor. These devices have not been studied to a continuous working. Any other use is
improper and forbidden and it could void manufacturer’s warranty. The manufacturer cannot be considered responsible for any damage due to improper, wrong
or unreasonable use. The installation of the product must be done by a qualified technician. At the end of the installation, all manuals must be given to the end
user. Keep this manual for future reference!
Dear customer, thank you for purchasing a MASTER product.
01
USER MANUAL
tubular motor Ø45 mm with electronic limit switch
R
rev01.1 14.06.2023
LINE
The technical characteristics of the motor are shown in the label applied to motor tube. Before installing the motor, it is recommended to copy the technical data
(including the full name of the product) and store them in a safe place. These data may be useful in the event of subsequent maintenance or technical
assistance. In addition to technical data on motor tube (depending on specific power of the motor), the common characteristics of the LINE motor family are:
Stand-by consumption :<1W
Operating temperature : -20 - +50°C
Min roller diameter :50x1.5mm
Power supply : 230 Vac 50 Hz
Operating frequency : 433.42 MHz
Insulation class :H
IP insulation : IP44
Max limit switch revolution: :
Memorizable transmitters : 40
Continuous operating time : 4 min
Memorizable wind radio sensors : 4
Memorizable sun radio sensors : 1
TECHNICAL SPECIFICATIONS
This product may have substances that are polluting for the environment and dangerous for the health.
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
Disposal
It is advisable (for example, near police stations, airports, ports, hospital, etc). A technical inspection is in any
case advisable before installing any radio system in order to identify sources of interference. Radio systems can be used where possible disturbances or malfunctioning of the
transmitter or the receiver do not cause a risk factor, or if the risk factor is cancelled by suitable safety systems. The presence of radio device operating on the same transmission
frequency ( ) can interfere with the radio receiver of the motor and so reduce the range of the system and limit the functionality of the installation.
to avoid using radio systems in areas with strong interference
433,42 MHz
Note on radio systems
Incorrect installation can cause serious injuries Keep these instructions for future maintenance work and disposal of the product All the product installation, connection,
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician Some applications require hold-to-run
operation and can exclude the use of radio controls or require particular safety devices To prevent potentially dangerous situations, check the operating condition of the roller
shutter/awning regularly
Before installing the product, check the compatibility with the associated devices and accessories Check that the package is intact and has not been damaged in transit A heavy
knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor Do not pierce or tamper with the motor in any way. Do not modify or replace
parts without the manufacturer's permission Do not carry the motor by the power cable. The product may not be used if the power cable is damaged. Do not try to replace the power
cable Any screws needed to complete the installation must not come into contact with the motor The power of the motor must be sufficient for the applied load (check the rated
data shown on the motor) Some stages of programming and/or normal operation make use of the mechanical stops of the roller shutter/awning. It is essential to choose a motor
with the most suitable torque for the application, considering the actual traction of the roller shutter/awning, and to avoid motors that are too powerful Use winding rollers that are at
least 1mm thick Leave 1-2 mm of right/left play on the winding roller Check that the shape and size of the drive pulley and adapter crown correspond to the winding roller used.
Adapters, supports and sundry accessories related to the motor must be chosen exclusively from the MASTER catalogue If the product is installed at a height of less than 2.5 m
from the floor or from another support surface, the moving parts must be protected with a cover to prevent accidental access. In any case, ensure access for maintenance work The
power cable must be positioned in such a way that it does not come into contact with moving parts The power cable of the product is suitable for indoor installation only. If installed
outside, place the cable in a protective tube If there are several radio appliances in the same system, they must not be less than 1,5m apart Do not install the product near metal
surfaces Position the buttons within sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor The motors are
designed for residential use; the maximum continuous operating time is 4 minutes During operation, the motor body becomes very hot, so be careful The motor contains a self-
resetting thermal cut-out, which stops the motor if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 5 to 10
minutes) The motor must be installed so that it cannot come into contact with liquids and in any case in a position protected from atmospheric agents The antenna cable carries
line voltage. Do not cut the antenna cable as this would be dangerous. If the antenna cable is damaged, replace the product For your safety, do not work near the winding roller while
the motor is powered
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or given instructions about the product way of use by a person responsible for their safety Check the automation during the movement and keep people at a safe
distance, until the movement ends Do not allow children to play with the appliance or with the fixed control devices Do not operate the blind when maintanance operations are
being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect the motor from the power line
1.2 Safety warnings for the INSTALLER
1.3 Warnings for USE
1.1 Safety warnings for the USER
WARNINGS
1
To Next Page
Loading...
Need help?
General
