MikroTik hAP ac3 LTE6 kit User Manual

The Mode Button enables the execution of custom scripts, that can be added by the user.
The , enables WPS mode.front blue LED button
Accessories
The package includes the following accessories that come with the device:
Operating system support
The device supports RouterOS software version 6.46. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.
Notice
The Frequency band 5.470-5.725 GHz isn’t allowed for commercial use.
In case WLAN devices work with different ranges than the above regulations, then a customized firmware version from the manufacturer/supplier
is required to be applied to the end-user equipment and also prevent the end-user from reconfiguration.
For Outdoor Usage: End-user requires approval/license from the NTRA.
Datasheet for any device is available on the official manufacturer website.
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 2.400 – 2.4835 GHz, the TX power is
limited to 20dBm (EIRP).
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 5.150 – 5.250 GHz, the TX power is
limited to 23dBm (EIRP).
Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 5.250 – 5.350 GHz, the TX power is
limited to 20dBm (EIRP).
Federal Communication Commission Interference Statement
The front LED bar displays LTE signal strength.
Please make sure the device has a lock package (firmware version from the manufacturer) which is required to be applied to the end-user
equipment to prevent the end-user from reconfiguration. The product will be marked with country code “-EG”. This device needs to be upgraded
to the latest version to ensure compliance with local authority regulations! It is the end users responsibility to follow local country regulations,
including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS)
requirements. All MikroTik radio devices must be professionally installed.
To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in
designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated
disposal sites in your area.

MikroTik hAP ac3 LTE6 kit Specifications

General

DSL WAN	No
Ethernet WAN	Yes
Antenna gain level (max)	5.5 dBi
Flash memory	16 MB
Certification	CE, FCC, IC, EAC, ROHS
Internal memory	256 MB
Processor cores	4
Processor model	Qualcomm Atheros IPQ4019
Processor frequency	716 MHz
Product type	Tabletop router
Product color	White
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	5
4G standard	LTE-TDD & LTE-FDD
SIM card type	MicroSIM
4G bands supported	700, 800, 850, 900, 1800, 1900, 2100, 2300, 2500, 2600 MHz
GSM bands supported	850, 900, 1800, 1900 MHz
UMTS bands supported	850, 900, 1900, 2100 MHz
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Wi-Fi band	Dual-band (2.4 GHz / 5 GHz)
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Top Wi-Fi standard	Wi-Fi 5 (802.11ac)
WLAN data transfer rate (max)	1167 Mbit/s
Output voltage	12 - 28 V
Power source type	DC
Operating temperature (T-T)	-30 - 60 °C

Weight and Dimensions

Depth	129 mm
Width	251 mm
Height	39 mm