MikroTik LtAP User Manual

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
This LtAP version is without a modem installed. In this case, an internal antenna is not connected.
Installing a miniPCIe module should be done by a qualified person, please follow safety precautions when handling electrical equipment, the device
supports two LR cards:
Use a wrist grounding strap when unpacking and working with electrical components to avoid electrical discharge (ESD) damage;
Remove six screws on the bottom of the case and lift off the top part of the case.
Locate the miniPCIe slot and remove two factory attached screws;
Attach provided a thick thermal pad to the card, and install the card into miniPCIe slot so that thermal pad is between PCB and card;
The secure card in place using previously removed two screws;
Connect internal antenna cables to your modem. Or guide your antenna cables through openings near the GPS connector and connect to the
modem. Recommended using silicone rubber to secure connectors in place.
Attach a thinner thermal pad to the top of the card;
When using external antennas, connectors can be attached on the case sides, to make openings use a 6.5 mm drill bit, please see Mounting
section part 4;
Please see the picture below for reference on how to place rubber seals for best water protection;
Reassembly in backorder. Tightening torque for PCB screws 0.3 Nm, case cover/enclosure screws 0.5 Nm.
After you have reinserted the device into the case and secured it with the screws that were removed earlier, slide in the SIM cards from your mobile
operator into the SIM slots, with the chips facing as shown on the port label. The slot accepts miniSIM (2FF). SIM slots 2 and 3 apply to the bottom
miniPCIe slot and can be switched in RouterOS "/system routerboard sim" menu.
Reset button
Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).
Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode. The device will now look for a CAPsMAN server (total 10
seconds).
Or keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15
seconds).
Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
Useful for RouterBOOT debugging and recovery.
Accessories
Package includes accessories that come with the device:
K-67 fastening set. Includes four screws 4x25 mm, four dowels 6x30 mm.
Cable DC (H4130-04PDB000R 3 mm 2x2P Housing) to (StripJacket 5 cm+WireEnd Strip/Tin 1 cm) 24 AWG (Black/Red/Blue/Orange) 0.35 m.
EU/US Switching Power Supply 24 V, 1.2 A, 28.8 W, 86.8%, VI, DC cable: 220 cm RA DC plug mod Hor CMC shorter plug.
Elastic thermal pads - 25x40x3.5mm +30x45x1mm in Ziplock bag.
Operating system support
The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.
Other operating systems have not been tested.

MikroTik LtAP Specifications

General

2.4 GHz	Yes
Networking standards	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	300 Mbit/s
Security algorithms	-
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN (RJ-45) ports	1
AC input voltage	12 - 30 V
Power consumption (max)	24 W
Product color	Black
Antenna type	Internal
Flash memory	16 MB
Internal memory	128 MB
Processor frequency	880 MHz
Operating temperature (T-T)	-40 - 70 °C
Number of products included	1 pc(s)
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	162 mm
Width	170 mm
Height	40 mm