MikroTik netPower 16P User Manual

Dashboard / UserManuals / Switches
netPower16P
netPower16P(CRS318-16P-2S+OUT)
ThenetPowerisaweatherproofswitchwiththecapabilityofdeliveringPoEtoyourconnecteddevices.
Quickstart
Pleasefollowthesequickstepstosetupyourdevice:
Openthebottomlid(see"netPower16P#BottomLid");
ConnectallserveddevicestoEthernetports;
Connectthedevicetothepowersource(see"netPower16P#Powering");
Onceconnectedtothesamenetwork,openhttps://192.168.88.1 inyourwebbrowsertostartconfiguration,username:adminandthereisnopasswordbydefault;
Onceconnectedconfigurethedevice,soithasanactiveInternetconnectionhttps://mt.lv/configuration;
UpgradetheRouterOSsoftwaretothelatestversionhttps://mt.lv/upgrade;
SetupyourrouterpasswordinthebottomfieldoftheQuickSetmenu,totherightandrepeatit,itwillbeusedtologinnexttime.
Expansionslotsandports
1. DCpowerconnector48–57V.
2. DCpowerconnector18–30V.
3. LEDindicatingapowerstateofthedevice.
4. Resetbutton.
5. GigabitEthernet,8-ports,deliveringPoEout.
6. GigabitEthernet,8-ports,deliveringPoEout.
7. Two-10GSFP+ports.
8. LEDIndicatingtheactivityofSFPport.
9. LEDIndicatingthespeedofSFPport.
Configuration
ThedevicecanbediscoveredusingWinboxutility,byclickingontheNeighborslist.Thedefaultmanagementaddressis192.168.88.1.Toreachbothdevicesneedstobein
thesameIPnetwork.Configuredasabridge,ARP,andfastforwardenabled.RSTPprotocolactivated.
RouterOSincludesmanyconfigurationoptionsinadditiontowhatisdescribedinthisdocument.Wesuggeststartingheretogetyourselfaccustomedtothepossibilities:
https://mt.lv/help.
Forrecoverypurposes,itispossibletobootthedeviceforreinstallation,seesection
netPower16P#ButtonsandJumpers.
Powering
Thedeviceacceptspowerinthetwowaysfollowingways:
Direct-inputpowerjack1,(5.5mmoutsideand2mminside,female,pinpositiveplug)accepts18-30VDC⎓.
Direct-inputpowerjack2,48-57VDC⎓.
UseincludedDCplugtoconnectwithyourpowersource:
1. DCplug2.1x5.5x12mmtoScrewTerminal2pin.
2. Connectyourpowersourcecablestothetwopinsandsecuretheminplacebytighteningscrews.
3. ConnectDCplugtothedevice.
Thepowerconsumptionundermaximumloadcanreach21W,withattachments325W.
Poweroutput
Thedevicesupports802.3af/atPoEfromEthernet1-16.YoucanpowerMikrotikdeviceswhichsupportspoweringthroughEthernet.ThepowerdeliveredthroughthePoE
ONTHISPAGE

MikroTik netPower 16P Specifications

General

Switch type	-
Switch layer	L2/L3
Flash memory	16 MB
Internal memory	256 MB
Processor model	98DX226S
Built-in processor	Yes
Processor frequency	800 MHz
Operating temperature (T-T)	-40 - 70 °C
Power connector	DC-in jack
SFP+ module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
DC input voltage	18 - 57 V
Power consumption (max)	316 W
10G support	No
Networking standards	IEEE 802.3af, IEEE 802.3at
Certification	CE/RED, EAC, RoHS
Product color	White
Forwarding rate	53.6 Mpps
MAC address table	- entries

Weight and Dimensions

Depth	78 mm
Width	212 mm
Height	303 mm